Who's Online Now
0 registered members (), 10 guests, and 3 spiders.
Key: Admin, Global Mod, Mod
April
S M T W T F S
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30
Newest Members
vacheera, KM Elevator, Shawzee, ChurchGuy, Luis Mariano
8461 Registered Users
Forum Statistics
Forums13
Topics6,507
Posts36,838
Members8,461
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#8360 - 09/04/13 05:11 PM Otis 411M Fire Service  
Joined: Feb 2010
Posts: 60
bk2fla Offline
Service Manager
bk2fla  Offline
Service Manager

Joined: Feb 2010
Posts: 60
south florida
hello all. I'm having an issue with the fire service. The car acts as if it is in fire recall (smoke alarms). It is sitting on the egress floor with doors open and the fire hat inside the car is flashing. If I turn Phase 2 on inside the car I can run the car in normal fire service fashion. The controller is showing EFO is on. On the module rack were my fire alarms tie into, the LED's show all alarms to be normal(which I verified).
I did notice,(compared to another car),on the module board there should be a blinking LED I'm guessing for communication that is not blinking. If I go into the parameters and set EFO to 0 the car runs on normal service although my fire hat is still blinking. Do you think my module board is bad? OCSS? MCSS? thanks for the help!!


All those who wonder are not lost
#8364 - 09/04/13 07:40 PM Re: Otis 411M Fire Service [Re: bk2fla]  
Joined: Jan 2011
Posts: 119
sccjr Offline
Shootintrouble
sccjr  Offline
Shootintrouble

Joined: Jan 2011
Posts: 119
Haven't worked on a 411 but have t/s 311's. I believe f/s is serial link right? Either way check your input for that particular input w/ your service tool. Also read the actual recall switch to see if its being recalled. You might have a bad addressing board for the fire service input. Lets assume the easiest before the more complicated which would be processor board.

#8368 - 09/05/13 02:21 AM Re: Otis 411M Fire Service [Re: sccjr]  
Joined: Jul 2013
Posts: 198
NewMech Offline
member
NewMech  Offline
member

Joined: Jul 2013
Posts: 198
Find the address of your RS5 or RS14 board in the prints, then use the tool to see if the BIT to that board is on. The board is in the COP. I have seen shitty connections on those little boards or damaged wiring make dumb stuff happen.

#8456 - 09/13/13 01:14 AM Re: Otis 411M Fire Service [Re: NewMech]  
Joined: May 2012
Posts: 194
Len Offline
member
Len  Offline
member

Joined: May 2012
Posts: 194
>>>>>>Does the car have Jamb lanterns and Lcd PI display..theses are all serial link related and all come off of the same RS14 remote..anyone of these can cause the fireman service Hat to falsely blink..

#8478 - 09/16/13 07:27 PM Re: Otis 411M Fire Service [Re: Len]  
Joined: Feb 2010
Posts: 60
bk2fla Offline
Service Manager
bk2fla  Offline
Service Manager

Joined: Feb 2010
Posts: 60
south florida
thanks I will check the state of the address. appreciate the help.


All those who wonder are not lost
#8536 - 09/21/13 11:12 AM Re: Otis 411M Fire Service [Re: bk2fla]  
Joined: Jun 2013
Posts: 2
Bluehaze Offline
stranger
Bluehaze  Offline
stranger

Joined: Jun 2013
Posts: 2
Melbourne, Australia
While testing the EFO status, keep in mind that sometimes it is wired as a "breaking" contact. I.e. The input goes off to activate the EFO mode. If this is the case, then a crook rs card will set that input as active and place the system on EFO. I owe a late night hair-pulling session to an experience of this on a single lift mcb job.

Last edited by Bluehaze; 09/21/13 11:24 AM.
#8728 - 10/17/13 03:12 PM Re: Otis 411M Fire Service [Re: Bluehaze]  
Joined: Oct 2012
Posts: 36
tony Offline
newbie
tony  Offline
newbie

Joined: Oct 2012
Posts: 36
Any luck....i think on those a blown fuse will latch fire service..


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.038s Queries: 14 (0.006s) Memory: 2.6961 MB (Peak: 2.8717 MB) Zlib disabled. Server Time: 2024-04-28 09:43:22 UTC