Who's Online Now
1 registered members (Jluff), 9 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
February
S M T W T F S
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28
Newest Members
JohnCR, Arteen, yaboymike, danlamber13, elevatorguy242
6421 Registered Users
Forum Statistics
Forums13
Topics5,045
Posts30,170
Members6,421
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#10265 - 04/01/14 06:13 PM 330A  
Joined: Jan 2010
Posts: 620
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 620
st.louis mo
Schindler 330A
GO# 06216-1

Description of problem
Starter picks and drops at ½ second intervals. Then down picks back and forth. With no demand.
LED,s start then why delta then up then down then start again over and over

Errors on LON ALL Log
1207
1213
1210
1230----all say EVLON problem software—or change EVLON Print


What we have tried Software 51513175 on 360 board 590960 on CRIPHNA board 2.2A ID.NR.223956
Replace CRIP board (twice) V3.81 (could be 61) V1.0
Replace 360 board 07.07.20 EBLON ½.Q
Replace EVCOM board IC-11 98-6-29
Eliminate viscosity control
Eliminate leveling sensors
We also tried draining capacitors on 360 board twice and this didn't work

Last edited by danzeitz; 04/01/14 06:13 PM.
#10267 - 04/01/14 10:59 PM Re: 330A [Re: danzeitz]  
Joined: Jan 2010
Posts: 21
PGL Offline
ELEVMAN
PGL  Offline
ELEVMAN

Joined: Jan 2010
Posts: 21
2 Questions will the car run on inspection.And have you replaced the CIO board in the car station?

#10270 - 04/02/14 04:12 AM Re: 330A [Re: PGL]  
Joined: Mar 2013
Posts: 51
rollaway-up Offline
2nd Generation
rollaway-up  Offline
2nd Generation

Joined: Mar 2013
Posts: 51
Canada
The cio board is a try, id look in the status -- I/0 menu and see if you can see what inputs are causing it to start. Check your khu, kse etc. and see if the vane reader is communicating. The vane reader plugs into cio before heading to crip. Maybe a bad cio board is causing the crip to think the car is lost? Altho id expect to see errors pertaining to that. Any other errors?

#10273 - 04/02/14 02:42 PM Re: 330A [Re: rollaway-up]  
Joined: Jan 2010
Posts: 620
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 620
st.louis mo
The car would run on automatic in the group (2 cars) This would only show up if you got the car lost. Pull main line at middle floor. After we tried new boards things got worse and it would screw up all the time. Car will not run on inspection now. And no we have not changed out the CIO board.

#10275 - 04/02/14 04:29 PM Re: 330A [Re: danzeitz]  
Joined: Jan 2010
Posts: 620
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 620
st.louis mo
Active inputs CDR-KNKT2 JNFF-OFF K-DRIP SDR-KNKT2 VST-S

#10278 - 04/03/14 04:24 AM Re: 330A [Re: danzeitz]  
Joined: Mar 2013
Posts: 51
rollaway-up Offline
2nd Generation
rollaway-up  Offline
2nd Generation

Joined: Mar 2013
Posts: 51
Canada
I would try the cio, it controls all the inputs and outputs for the positioning. I've had strange things happen before. To be clear in my understanding: the car runs fine on auto but if you kill the power when its not at the terminal it will hunt for a position by cycling directions?

Also you say It does not run on inspect, on the crip there are relays SKD1-5, which is basically your safety circuit. When you give start command are these all lighting up?

#10279 - 04/03/14 11:27 AM Re: 330A [Re: rollaway-up]  
Joined: Jan 2010
Posts: 620
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 620
st.louis mo
The car use to run fine on auto and then if it became lost it would start hunting for position. Now it hunts for position all the time. We will install CIO today. and will check skd1-5 if CIO doesn't fix it.

#10280 - 04/03/14 05:59 PM Re: 330A [Re: danzeitz]  
Joined: Jan 2010
Posts: 620
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 620
st.louis mo
CIO board did the trick Thanks for the help!!!!!

#10285 - 04/04/14 11:51 PM Re: 330A [Re: danzeitz]  
Joined: Mar 2012
Posts: 102
Elevatorfella Offline
member
Elevatorfella  Offline
member

Joined: Mar 2012
Posts: 102
Is it possible that its in viscosity control and bypass is not set correcty? Levelling sensors a bit too close? Just a thought, I'm on vac. In Jamaica and waiting for wife to shower. Just a couple quick thoughts

#10286 - 04/05/14 02:51 AM Re: 330A [Re: Elevatorfella]  
Joined: Jan 2012
Posts: 865
jkh Offline
4 Ever Learning.
jkh  Offline
4 Ever Learning.

Joined: Jan 2012
Posts: 865
Ah Jamaica!
I've been there several time. Swept Away in Negril is one of my favorite places.

Where are you staying?


Make good choices,

JKH
#10287 - 04/05/14 04:11 AM Re: 330A [Re: danzeitz]  
Joined: Mar 2013
Posts: 51
rollaway-up Offline
2nd Generation
rollaway-up  Offline
2nd Generation

Joined: Mar 2013
Posts: 51
Canada
And more importantly, snap some pictures of the equipment! My father did some consulting work down there, seemed pretty laid back!

#10292 - 04/06/14 01:09 AM Re: 330A [Re: jkh]  
Joined: Mar 2012
Posts: 102
Elevatorfella Offline
member
Elevatorfella  Offline
member

Joined: Mar 2012
Posts: 102
Dude, at Swept Away.....in room 3116 by the hot tub in the middle of the resort! This is our 2nd trip here. Headed back to reality tomorrow. Absolutely Love this place

#10297 - 04/06/14 05:37 PM Re: 330A [Re: Elevatorfella]  
Joined: Jan 2012
Posts: 865
jkh Offline
4 Ever Learning.
jkh  Offline
4 Ever Learning.

Joined: Jan 2012
Posts: 865
"Great mind think alike"

Sorry for reality to set in. But, glad you enjoyed your stay.


Make good choices,

JKH
#10298 - 04/06/14 05:42 PM Re: 330A [Re: jkh]  
Joined: Jan 2012
Posts: 865
jkh Offline
4 Ever Learning.
jkh  Offline
4 Ever Learning.

Joined: Jan 2012
Posts: 865
My Wife wants to know if you tried the wood over pizza after you worked out at the sports complex?


Make good choices,

JKH

Photo Gallery
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Uncle Dad Here?
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.034s Queries: 14 (0.007s) Memory: 2.7517 MB (Peak: 2.9871 MB) Zlib disabled. Server Time: 2021-02-26 01:05:24 UTC