Who's Online Now
0 registered members (), 24 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#10870 - 05/29/14 09:28 PM 211 LADS Fault  
Joined: Oct 2009
Posts: 404
Scott Davidson Offline
troubleshooter1
Scott Davidson  Offline
troubleshooter1

Joined: Oct 2009
Posts: 404
california
mechanic says he cannot reset LADS fault. i had him check to see if lower access door input was going low when door opens. also checked that the input was going low when the CIO check was low, and it all checked out ok. if he removed the wire from the cio output that went to the door locks, put the car on inspection and reset the fault, the car indicates inspection operation, as soon as he puts the wire for the door lock circuit back on, the lads fault appears, car will only run from access in the hall, will not run from mr inspection. he sent the cpu board in for repair. any other things to look for? he is hoping the board will fix the problem but just looking for ideas in case it does not thanks

Last edited by Scott Davidson; 05/29/14 09:30 PM.
#10884 - 05/31/14 12:12 AM Re: 211 LADS Fault [Re: Scott Davidson]  
Joined: Dec 2010
Posts: 566
elmcannic Offline
addict
elmcannic  Offline
addict

Joined: Dec 2010
Posts: 566
S. Central Utah
The unit only runs from the hall on access (with the LADS bypassed), not when all doors are closed (MRI). I wonder if there is an issue at the access key switch or the interlock wires are swapped and some sort of safety redundancy circuit is catching it. I don't know much about that CIO testing. Did this issue just suddenly occur do you know? And the resetting...is he using the two SW (2&3?) button commands or simply the "reset" button to try to clear the fault? Just asking.

Last edited by elmcannic; 05/31/14 12:18 AM.
#10886 - 05/31/14 03:37 AM Re: 211 LADS Fault [Re: elmcannic]  
Joined: May 2012
Posts: 194
Len Offline
member
Len  Offline
member

Joined: May 2012
Posts: 194
Sounds like a wiring cross between...Hds and Lads...inputs...

#10887 - 06/01/14 01:15 AM Re: 211 LADS Fault [Re: Len]  
Joined: Oct 2009
Posts: 404
Scott Davidson Offline
troubleshooter1
Scott Davidson  Offline
troubleshooter1

Joined: Oct 2009
Posts: 404
california
this has been a running car, no problems the last 2 years. the car won't run from mr inspection, and the door inputs are on. i know the reset is working, because he can reset it, and take the cio output wire off, and the car will not have the fault, just no door lock input, as soon as the cio wire is put back on, the fault comes on immediately. he says dol, and dcl are also working properly, the board will be back next week and we will see what happens. thanks


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.089s Queries: 15 (0.041s) Memory: 2.6693 MB (Peak: 2.8199 MB) Zlib disabled. Server Time: 2024-03-29 06:22:10 UTC