Who's Online Now
0 registered members (), 9 guests, and 1 spider.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,466
Posts36,640
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
Page 2 of 2 1 2
#33395 - 07/14/22 12:23 AM Re: Dover Composite [Re: DripCan]  
Joined: Jun 2017
Posts: 93
boomer Offline
journeyman
boomer  Offline
journeyman

Joined: Jun 2017
Posts: 93
Are you looking for some specific info?

#33396 - 07/14/22 01:04 AM Re: Dover Composite [Re: Fduncan]  
Joined: Apr 2020
Posts: 389
Montana Offline
enthusiast
Montana  Offline
enthusiast

Joined: Apr 2020
Posts: 389
Email address?

#33397 - 07/14/22 12:56 PM Re: Dover Composite [Re: boomer]  
Joined: Jun 2022
Posts: 2
Fduncan Offline
stranger
Fduncan  Offline
stranger

Joined: Jun 2022
Posts: 2
I recently picked up a building on my route and here goes. I’m working on a 12 stop Dover composite. It is a duplex, but whoever had them before me removed the top mounted selector and installed some kind of electronic one on elevator #1, that elevator is currently out of service and to my knowledge has been for some time. That isn’t the one I’m working on though, the one I’m working on has original selector on top and was operating fine until about 2 weeks ago when the down calls on floors 2, 3, and 4 stopped working. It would take an up call but no down call from those floors. All calls worked on other floors. Over the past 2-3 days this elevator has stopped working completely, then it started going to random floors when any call was given, then without changing anything would start going from top to bottom nonstop cycling doors at those landings. After cleaning the sleds and the top mounted selector and checking and cleaning all of the ibm relays carefully it started working properly for about 10 minutes then started going from top to bottom again no matter what call was given. Then all of sudden while I was going prints that are on jobsite but not clearly not for this particular job the elevator started taking up calls and going to designated floor just fine, on the down call it would go to the floor below the designated call, cycle doors then go up one floor to designated call. After about and hours or so of that it started stopping at every floor cycling doors no matter what call or which direction. After a 17 hour day I went home last night, came back this morning and it’s back to running top to bottom. I’m at a complete loss, and I’ve only got one other composite on my route at the moment so I’m not real familiar with these. Any and all advice is much appreciated. Work safe!

#33662 - 08/13/22 05:31 PM Re: Dover Composite [Re: DripCan]  
Joined: Aug 2022
Posts: 5
Bobbybolognie Offline
stranger
Bobbybolognie  Offline
stranger

Joined: Aug 2022
Posts: 5
Not sure where to post this but here goes.
Customer owns the old NY Telephone building in Newark, NY 14513 (near I90, Western NY between Rochester & Syracuse). Looking for some experienced with the Dover Composite System to troubleshoot & repair it. We’re trying to get the prints from TKE Elevator but not sure we’re going to get them. Please share this with techs that could help. Thanks Bob. 803-640-7096

#33668 - 08/13/22 09:41 PM Re: Dover Composite [Re: DripCan]  
Joined: Jan 2010
Posts: 662
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 662
st.louis mo
Email address

#33671 - 08/14/22 06:18 PM Re: Dover Composite [Re: DripCan]  
Joined: Aug 2022
Posts: 5
Bobbybolognie Offline
stranger
Bobbybolognie  Offline
stranger

Joined: Aug 2022
Posts: 5
rvseverson@hotmail.com

#33714 - 08/19/22 03:30 PM Re: Dover Composite [Re: DripCan]  
Joined: Apr 2020
Posts: 5
Upndn40yrs Offline
stranger
Upndn40yrs  Offline
stranger

Joined: Apr 2020
Posts: 5
What info are you looking for?

#33903 - 09/20/22 02:20 PM Re: Dover Composite [Re: Upndn40yrs]  
Joined: Aug 2022
Posts: 5
Bobbybolognie Offline
stranger
Bobbybolognie  Offline
stranger

Joined: Aug 2022
Posts: 5
I was looking for someone to work on this elevator. Since my last post we got a scanned copy the original schematics. The quality is poor. Now I'm trying to get the schematics reworked so we can read them.

#34070 - 10/19/22 12:23 AM Re: Dover Composite [Re: DripCan]  
Joined: Oct 2022
Posts: 2
BB King Offline
stranger
BB King  Offline
stranger

Joined: Oct 2022
Posts: 2
Old post I know… but I picked up 4 composites(2 sites) this month and have a partial print on one. Would anyone be willing to share their composite library please.
Thanks in advance!

Page 2 of 2 1 2

Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.032s Queries: 16 (0.009s) Memory: 2.7200 MB (Peak: 2.9143 MB) Zlib disabled. Server Time: 2024-03-28 08:42:05 UTC