Who's Online Now
0 registered members (), 44 guests, and 3 spiders.
Key: Admin, Global Mod, Mod
May
S M T W T F S
1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30 31
Newest Members
vacheera, KM Elevator, Shawzee, ChurchGuy, Luis Mariano
8461 Registered Users
Forum Statistics
Forums13
Topics6,515
Posts36,882
Members8,461
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#19517 - 02/10/17 04:53 PM schindler 300  
Joined: Jan 2010
Posts: 87
Jim Offline
journeyman
Jim  Offline
journeyman

Joined: Jan 2010
Posts: 87
car is found shut down level at bottom landing. 3 stops. front only. go to plug in with hht. car starts up again. goes into viscosity control. and is ready for action. usually the call comes in on monday. i tried recreating it. hit the manual lowering and it relevels no problem. cleaned the levelling sensors and mirrors. checked the power supplies. all where they should be. has anybody had this problem with these wonderful controls?

#19522 - 02/10/17 07:28 PM Re: schindler 300 [Re: Jim]  
Joined: Aug 2016
Posts: 755
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 755
What is the shut down code ?

#19524 - 02/10/17 09:03 PM Re: schindler 300 [Re: Jluff]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
What type of valve is on it? Have you cleaned screens?

#19569 - 02/13/17 08:06 PM Re: schindler 300 [Re: Rolly]  
Joined: Jan 2010
Posts: 87
Jim Offline
journeyman
Jim  Offline
journeyman

Joined: Jan 2010
Posts: 87
eeco uv5a valve. screens are clean. no logged faults.

#19570 - 02/13/17 10:34 PM Re: schindler 300 [Re: Jim]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
Does job have a tank heater??? It sounds like a viscosity problem.

Last edited by Rolly; 02/13/17 10:34 PM.
#19587 - 02/15/17 02:04 PM Re: schindler 300 [Re: Rolly]  
Joined: Jan 2012
Posts: 885
jkh Offline
4 Ever Learning.
jkh  Offline
4 Ever Learning.

Joined: Jan 2012
Posts: 885
Did you put a gauge on the valve, pull the main line and shut the gate valve in the hydraulic line?


Make good choices,

JKH
#19758 - 03/02/17 05:49 PM Re: schindler 300 [Re: jkh]  
Joined: Jan 2010
Posts: 87
Jim Offline
journeyman
Jim  Offline
journeyman

Joined: Jan 2010
Posts: 87
i found the lu and ld sensors too close together. so i spread them to the factory reommended spacing. then it was stopping early in the down. the valve was set to glide into the floor. now i have stabilized levelling and a firm stop. i installed a tank heater too. im not sure which of those two items fixed it. but it hasnt shut down for over a week now. which is a new record. its been this way for 10 years. but the site caretaker had been resetting it for years without our knowledge. now hes gone. i hate when people dont follow up with what their fix was. so i figured i should. maybe it will start to become the norm around here.

#19759 - 03/02/17 06:01 PM Re: schindler 300 [Re: Jim]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
Thanks for the follow up!


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.155s Queries: 14 (0.023s) Memory: 2.7033 MB (Peak: 2.8890 MB) Zlib disabled. Server Time: 2024-05-05 19:12:16 UTC