0 registered members (),
21
guests, and
2
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums13
Topics6,515
Posts36,882
Members8,461
|
Most Online117 Jan 16th, 2020
|
|
|
#21697 - 09/23/17 12:14 AM
TAC 20 Linear PA6 door operator
|
Joined: Apr 2016
Posts: 25
Dandroid
newbie
|
newbie
Joined: Apr 2016
Posts: 25
|
Anyone had any luck recently upgrading from a PA_ to a PA6 LDO? Last 3 I've tried I've had no luck with.
Most recently, gotta TAC 20-03 with a PA3 that got burned up by water getting into the box after a storm. Still could connect to it so I downloaded the config successfully. Put the new PA6 in with same jumper settings, left the motor plug out. Fired it up, and uploaded the old board config. Reset it, checked my profiles and parameters. It didn't seem to have changed anything from the defaults, so I went through and changed the relevant settings manually, and saved, reset. The door just jerks around though. Tried the generic config, same thing.
It's a LH linear, so I have LHO=1, LDO=1, ELI=1, DCM=1, plus others I don't remember now.
Last 3 I've tried to program have done basically the same thing. Not sure about the status of the other 2 since they're out of my area, but I'm stuck with this one.
Last PA6 I successfully installed was about 2 years ago, and I remember exactly what I did. It was easy as heck and I was out the door in 20 minutes. Match jumpers, download config from old board, install new one, upload old config, reset, and done.
Only thing I'm seeing is the software version numbers: 2.17 for the PA3, and 2.24 for the new PA6.
What am I missing? Did something change in the software that I don't know about? I'm using the same laptop I've used for the past ~2 years.
I've also tried putting the door profile into the door board directly using the 4-pin serial adaptor and hyperterminal - it connects fine, but then when I send the file, it gives me a status of "file rejected", and fails the transfer.
|
|
|
#21722 - 09/25/17 07:54 PM
Re: TAC 20 Linear PA6 door operator
[Re: Dandroid]
|
Joined: Feb 2017
Posts: 8
CinciElevator
stranger
|
stranger
Joined: Feb 2017
Posts: 8
|
What are the doors doing that Causes concern? Can you run them open and close with mdo mdc? Are they running in correct direction? Does the board you are using have the uit on it? Also what jumpers are on and off? I would make certain jumpers are correct and if I remember right the replacement cards were preset to ac profile.
Last edited by CinciElevator; 09/25/17 08:00 PM. Reason: Info
|
|
|
#21725 - 09/25/17 10:59 PM
Re: TAC 20 Linear PA6 door operator
[Re: Dandroid]
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
What position is jp5 jumper on? That changes communication type, 485 or can.
If all else fails, read the instructions
|
|
|
|
|