Who's Online Now
0 registered members (), 11 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#23859 - 04/26/18 05:52 AM Otis MCS 120 Hyd. with Bucher  
Joined: Jan 2016
Posts: 39
Yus123 Offline
newbie
Yus123  Offline
newbie

Joined: Jan 2016
Posts: 39
Dear All

I have a problem with MCS 120 Hydraulic with Bucher valve.
The lift very often has a problem with fault log DBSS only with status fault on Otis tool DAR ST.
Whenever has an error the call is not registered and will working Normal again after we reset the power supply OFF and ON.
We have changed the Bucher selenoid, the new LCB2 board. PSR switches, whole the contactors including LV1, LV2, and LVC.

Appreciate for your help. Thank in advance.

Attached Files
ErrLog.JPG (43 downloads)
#23861 - 04/26/18 06:44 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Aug 2014
Posts: 134
Alex75 Offline
member
Alex75  Offline
member

Joined: Aug 2014
Posts: 134
Sweden
Hi Yus123

Does the lift have a pawl device?
If yes, try to disable the Anti Creep Device for testing purpose. Set parameter in LCB-II M1-3-1-4 (Drive parameters) ACD/UXT = 0 (Disabled).

/Alex

Last edited by Alex75; 04/26/18 06:48 PM.
#23873 - 04/29/18 05:14 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Jan 2016
Posts: 39
Yus123 Offline
newbie
Yus123  Offline
newbie

Joined: Jan 2016
Posts: 39
Hi Alex75,

We checked on site the parameter already disabled.
Since 3 years maintained the lift, we have changed Bucher selenoid valve 3 times already

Attached Files
16_Drive.jpeg (39 downloads)
#23884 - 04/30/18 06:50 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Aug 2014
Posts: 134
Alex75 Offline
member
Alex75  Offline
member

Joined: Aug 2014
Posts: 134
Sweden
Hi Yus123

It looks like the only things that can generate the DAR state is:

- Fault from the Bucher control (Is the relay on the Bucher Power Supply connected?, If yes try to bridge this relay).
- Or one of these inputs have been active: OTS (Oil Temp Switch), PLS (Pressure Limit Switch), MPD (Motor Protection Device), THB (Thermo Contact).

/Alex

Last edited by Alex75; 04/30/18 07:00 AM.
#23897 - 05/02/18 05:32 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Alex75]  
Joined: Jan 2016
Posts: 39
Yus123 Offline
newbie
Yus123  Offline
newbie

Joined: Jan 2016
Posts: 39
Hi Alek75,

Thank you for your advice, I will check on site and let you know.

Best Regards
Yustinus

#23911 - 05/03/18 08:32 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Feb 2018
Posts: 1
Pjalle Offline
stranger
Pjalle  Offline
stranger

Joined: Feb 2018
Posts: 1
Hello

Did You properly set the 0-value of the Bucher valve?
What kind of controller do You have of the Bucher?

#23940 - 05/06/18 06:32 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Pjalle]  
Joined: Jan 2016
Posts: 39
Yus123 Offline
newbie
Yus123  Offline
newbie

Joined: Jan 2016
Posts: 39
hello Pjalle,

I have not checked yet about the 0 value of Bucher Valve, could you advise me how to check this, please
I have checked the 0 value on parameter LCB_2 only.
the controller of the Bucher is Delcon Controller.

#32845 - 04/04/22 09:17 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: May 2012
Posts: 88
sampler Offline
journeyman
sampler  Offline
journeyman

Joined: May 2012
Posts: 88
Dear Yus123, I have the same problem. Did you solve it. Can you help. Also Bucher 0-point has already been set and problems' going on.

#32852 - 04/05/22 04:38 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Apr 2014
Posts: 263
heisenberg Offline
Engineer
heisenberg  Offline
Engineer

Joined: Apr 2014
Posts: 263
Is there an error led showing on the Bucher delcon card when it faults?

Is it faulting during travel? Specifically in the down?
Do NOT touch the 0 point adjustment unless absolutely necessary.

You may need Bucher delcon hand tool to check Bucher system errors

#32914 - 04/08/22 06:50 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: May 2012
Posts: 88
sampler Offline
journeyman
sampler  Offline
journeyman

Joined: May 2012
Posts: 88
The error occurs in the morning and always car at the bottom floor, not actived final switch but 12 cmm down.

hand tool errror: Warn: Bypass pr, Demand, problems keep on. thanks.

#32922 - 04/11/22 07:53 AM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Apr 2014
Posts: 263
heisenberg Offline
Engineer
heisenberg  Offline
Engineer

Joined: Apr 2014
Posts: 263
Is it possible that the hydraulics are seeping too much when sitting idle?

Try changing the parking floor

#32925 - 04/11/22 04:31 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: May 2012
Posts: 88
sampler Offline
journeyman
sampler  Offline
journeyman

Joined: May 2012
Posts: 88
dear heisenberg, normally relevelling is working very well and many times tested. After hours, releveling may not occur due to cold oil or a valfe fail? So if I set parking floor for a diffrent floor samething may happen? But I tried floor changing to test.
As you say I set the parking floor "ARD-P and ARD-T". but controller malfunctioning. car goes for parking floor (screen turns ARD from IDL). then goes bottom floor (Service tool's screen shows PRK). again and again this keeps on. so I closed these parameters.

#32929 - 04/11/22 09:38 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Feb 2013
Posts: 757
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 757
ohio
Is there a tank heater? Or does this run the motor to heat the oil? If it runs the motor to heat, make sure the valve isn't moving the car when it is heating.

#32933 - 04/12/22 05:47 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: May 2012
Posts: 88
sampler Offline
journeyman
sampler  Offline
journeyman

Joined: May 2012
Posts: 88
there is no heater. if oil temperature is the reason of this failure there's a reverse situation. Cause relevelling can not occur due to cold oil.

#32934 - 04/12/22 06:14 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Nov 2009
Posts: 408
Johnny Offline
Journeyman
Johnny  Offline
Journeyman

Joined: Nov 2009
Posts: 408
Portland. Oregon
Is there a low pressure setting for this valve? Is there a maximum number of relevels allowed?

#32935 - 04/12/22 07:09 PM Re: Otis MCS 120 Hyd. with Bucher [Re: Yus123]  
Joined: Feb 2013
Posts: 757
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 757
ohio
I would certainly put a tank heater in, you have tried everything else. A cheap workaround, just to see if oil temp is the issue is to put a heat lamp on the valve. It may give you an idea. Just a thought.


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.045s Queries: 17 (0.017s) Memory: 2.7666 MB (Peak: 3.0242 MB) Zlib disabled. Server Time: 2024-03-29 08:35:46 UTC