Who's Online Now
0 registered members (), 19 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#24722 - 09/12/18 01:38 PM KONE KCM OPERATOR INTERFACE  
Joined: Jan 2015
Posts: 117
Turbo6 Offline
member
Turbo6  Offline
member

Joined: Jan 2015
Posts: 117
Chicago
My question is that can there operator be easily interfaced with another controller like a Smartrise/Mce ect? I havnt seen one and I don't know if there serial controls to controller. Doing a mod on one and trying to decide to replace it or not. If I have to replace is there a direct swap out there?

#24723 - 09/12/18 02:10 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Dec 2009
Posts: 534
solidstate Online content
addict
solidstate  Online Content
addict

Joined: Dec 2009
Posts: 534
Smartrise would answer that my two cents if u r going to mod the controller get rid of all of that expensive Kone stuff

#24724 - 09/12/18 02:49 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: May 2011
Posts: 330
ABE Offline
Mechanic
ABE  Offline
Mechanic

Joined: May 2011
Posts: 330
I think it would depend on the operator. If its the linear AMD(Wittur) operator I think they just use discreet wiring as I have seen them used with a variety of other controllers such as smart rise, MCE and Virginia controls.

#24731 - 09/13/18 01:47 AM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Ya, just looked at a print to make sure but the AMD operators are discreet to the CCBN board. 24vdc logic, open & close inputs, open & close limit outputs, and edge detector output. Don’t see a nudge or reduced speed input though, at least not on the KCM print.

#24732 - 09/13/18 02:01 AM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Looks like reduced speed is activated by giving an open and close command at the same time, pulling 16 & 17 low. But the operator does have a nudge input.

Last edited by Indirtwetrust; 09/13/18 02:10 AM.
#24740 - 09/13/18 07:08 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Oct 2013
Posts: 113
chicago Offline
member
chicago  Offline
member

Joined: Oct 2013
Posts: 113
You can install Kone AMD operator on any controller. You need to call spares. Need expansion board that mounts next to operator board, controls signals to controller.
Best operator on market, it will eliminate night callouts!!

#24782 - 09/14/18 09:56 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Jan 2015
Posts: 117
Turbo6 Offline
member
Turbo6  Offline
member

Joined: Jan 2015
Posts: 117
Chicago
Thanks fellas, we are going to give konespares a call.

#24784 - 09/14/18 09:57 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
May as well bend over.. LOL

#24930 - 10/06/18 02:38 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Jan 2015
Posts: 117
Turbo6 Offline
member
Turbo6  Offline
member

Joined: Jan 2015
Posts: 117
Chicago
This was the ADM 1.5 and it uses discrete 24vdc inputs so I was able to make it work. Only hiccup was I needed to add relays for the operators outputs because they are of the sinking type.

#24932 - 10/06/18 03:37 PM Re: KONE KCM OPERATOR INTERFACE [Re: Turbo6]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Good job. I knew you could make it work.


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.032s Queries: 15 (0.008s) Memory: 2.7167 MB (Peak: 2.9171 MB) Zlib disabled. Server Time: 2024-03-29 13:38:32 UTC