Who's Online Now
0 registered members (), 14 guests, and 1 spider.
Key: Admin, Global Mod, Mod
September
S M T W T F S
1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30
Newest Members
zfarzam, allonsy87, Vishalsakhreliya, ZMedina, JH elevator
6708 Registered Users
Forum Statistics
Forums13
Topics5,296
Posts31,295
Members6,708
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#27102 - 06/02/19 11:18 PM Garaventa Elvoron Info  
Joined: Jan 2018
Posts: 7
Flying Ron Offline
stranger
Flying Ron  Offline
stranger

Joined: Jan 2018
Posts: 7
I've got the prints and a list of fault codes for this elevator. I was trying to reset the positions on the landings in learn mode. I think I did it right. What I did was move the jumper to the Learn Mode position and move the NORM/INS switch to INS. Positioning the elevator on the first floor with the Up/Down buttons then twiddle the INS switch and wait for the floor display to change to one. Repeat for floors 2 and 3. Am I doing this right?

#27103 - 06/02/19 11:34 PM Re: Garaventa Elvoron Info [Re: Flying Ron]  
Joined: May 2013
Posts: 209
Jcjmowrey Offline
enthusiast
Jcjmowrey  Offline
enthusiast

Joined: May 2013
Posts: 209
Atlanta ga
Sounds about right. I know you have to make sure the encoder led’s behind COP are pulsing. I’ve had to replace the encoder 3 times on one of the units and finally went with a different manufacturer.


If all else fails, read the instructions
#27105 - 06/03/19 12:40 AM Re: Garaventa Elvoron Info [Re: Flying Ron]  
Joined: Nov 2009
Posts: 309
Johnny Offline
Journeyman
Johnny  Offline
Journeyman

Joined: Nov 2009
Posts: 309
Portland. Oregon
Start with cab above the reset magnet. Put on inspection and install learn jumper. Move car to bottom floor, when you have it positioned, hold both 1 & 2 car pushbuttons until the display changes to 1. Move car to 2. Hold both 1 & 2 car pushbuttons until the display changes to 2. Remove learn jumper.

#27106 - 06/03/19 12:42 AM Re: Garaventa Elvoron Info [Re: Flying Ron]  
Joined: Nov 2009
Posts: 309
Johnny Offline
Journeyman
Johnny  Offline
Journeyman

Joined: Nov 2009
Posts: 309
Portland. Oregon
move car to 3 and hold both 1 & 2 car pushbuttons until the display changes to 3. After all floors set, remove learn jumper.

#27108 - 06/03/19 02:01 AM Re: Garaventa Elvoron Info [Re: Flying Ron]  
Joined: Jan 2018
Posts: 7
Flying Ron Offline
stranger
Flying Ron  Offline
stranger

Joined: Jan 2018
Posts: 7
OK, that's pretty much what I was doing only I held all three buttons down (I guess 3 was redundant).

The encoder is probably OK. It's just that I guess things have stretched or whatever over the two years since this was installed and there was about a 1/2 lip that made it hard to move carts in and out of the thing.

Thanks for the confirmation.


Photo Gallery
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Uncle Dad Here?
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.060s Queries: 14 (0.017s) Memory: 2.6788 MB (Peak: 2.8405 MB) Zlib disabled. Server Time: 2021-09-22 14:01:03 UTC