Who's Online Now
1 registered members (Indirtwetrust), 14 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,653
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#28345 - 12/02/19 11:55 AM DMC. RER ?  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Hello. Trying to do a learn run after power outage and programming lost. Every time I gets to the 2nd floor magnets I get a RER which is reset error flag command from CLC. What do you guys think the problem is ? Bad selector board ? A side note. My clc is only letting me set it up as the master car of a group. But it’s a single car. No group

Last edited by Jluff; 12/02/19 12:11 PM.
#28347 - 12/02/19 01:16 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
It also will not let me set up valid floor openings which I have never seen before

#28348 - 12/02/19 02:36 PM Re: DMC. RER ? [Re: Jluff]  
Joined: May 2015
Posts: 287
wltr00 Offline
enthusiast
wltr00  Offline
enthusiast

Joined: May 2015
Posts: 287
Sounds like the power outage may have corrupted your software.

#28349 - 12/02/19 02:37 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I think once I saw error code saying it didn’t get slow down when run learn failed and RER showed on tool

#28351 - 12/02/19 05:11 PM Re: DMC. RER ? [Re: wltr00]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I have never replaced DMC software. Only the clc board but used existing chips. Does world electronics sell software chips ?

#28352 - 12/02/19 05:27 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Today I went to try run learn again and now I get no response from device when service tool is connected. . I isolated the clc board and still got no response from device. Tomorrow I will replace clc and put the existing chips in the new clc .. now I’m really getting confused as to what’s going on. Lol.

#28353 - 12/02/19 05:42 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
Does your board have 3 chip plus ram or 4 chip plus ram? A new board will require the 4 chip software. I believe it's ver DK13. If you have more then one car, all will have to be updated if duplex or triplex.

Last edited by Rolly; 12/02/19 05:45 PM.
#28354 - 12/02/19 06:40 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I see 3 chips with DMC1 stickers on them from the existing board

#28355 - 12/02/19 06:41 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I can send you a picture if you PM me your email

#28364 - 12/03/19 01:40 AM Re: DMC. RER ? [Re: Jluff]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
I’m not sure about that RER but older software didn’t support the valid floors parameters yet so probably nothing wrong there. There are basically 2 types of CLC cards. Old ones like BP1, BP2 and the first one that just had a number and then there is the BP4. Software is not interchangeable between the 2 types. DK13 is the latest for the BP4 boards but for the older it’s AN13. If you have an older board and all you can get is a BP4, you will need new software.

#28369 - 12/03/19 02:31 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
The new green clc has no ram
Chips in the U32 (SP23) and U33 (sp45) spots. The new clc only has a chip in the U31 spot .. the new board will not boot up with the software chips from the old board. Should I bring boards to computer technition to transfer chips from old board to new board ?

#28372 - 12/03/19 05:06 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
LOL ALL computers have ram. The chip may be soldered in but it has ram! 3 chip software will not work on a new board. I think you been told this before,

#28373 - 12/03/19 06:24 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I recognize ram on both boards. They are not set up the same and there was no markings on the board. I couldn’t tell if bp1 or 2 or 4. I think it is a bp1. And my new board is bp4. Just learning and trying to do my job Rolly

Last edited by Jluff; 12/03/19 06:27 PM.
#28377 - 12/04/19 12:15 AM Re: DMC. RER ? [Re: Jluff]  
Joined: May 2015
Posts: 287
wltr00 Offline
enthusiast
wltr00  Offline
enthusiast

Joined: May 2015
Posts: 287
Should have part number 6300BPx right on board, but older versions are blue & newer versions are green. The software between old & new boards is not compatible.

#28380 - 12/04/19 02:47 AM Re: DMC. RER ? [Re: Jluff]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Like I said, the old software will not work in your new BP4 CLC. You either need to find a good BP2 or earlier or order DK13 software.

#28403 - 12/05/19 05:03 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Got a new BP1 CLC and Im all set. Back to original problem during hoist way set up for 3 stop car. Getting fault missing slowdown when at 2nd floor. Switch tree is out play at 2nd floor. Cams are at terminal landings only. I Pulled up tree anyway and everything looks good. Magnets look good also

#28409 - 12/05/19 10:55 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Sounds like it thinks it’s a 2 stop


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.034s Queries: 15 (0.008s) Memory: 2.7728 MB (Peak: 3.0327 MB) Zlib disabled. Server Time: 2024-03-28 23:33:11 UTC