Who's Online Now
0 registered members (), 11 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#28502 - 12/30/19 10:34 PM miprom21  
Joined: Jan 2014
Posts: 130
DripCan Offline
member
DripCan  Offline
member

Joined: Jan 2014
Posts: 130
took over new job an 1 of the cars been powered off for over year for new doors.Powered up to replace doors an think unit lost memory have kone tablet tried reinitiate drive an keep getting about half way an screen goes blank if i get it to finish i get fault f param from eeprom also checked mismatches an see them but dont know which one is correct number.Was told to do a initiate drive but afraid everything will go to default an i wont know which parameters numbers mean what. It has the Allen Bradley dc drive

#28504 - 12/31/19 02:05 AM Re: miprom21 [Re: DripCan]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
You’re going to have to do an init. In most cases it will run with default parameters.

#28505 - 12/31/19 02:10 AM Re: miprom21 [Re: DripCan]  
Joined: Feb 2013
Posts: 757
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 757
ohio
If this is part of a group, or a duplex you can look at those parameters. If you init the drive, you will lose all the field programmable parameters. The f mismatch is saying that one or more of the field programmable parameters stored in the drive, do not match the the the ones stored in the Miprom. you should check them one by one. parameters such as motor RPM's, car speed, armature amps, the list goes on.Check these in MSU adjust, and drive adjust screens.

#28506 - 12/31/19 02:15 AM Re: miprom21 [Re: Indirtwetrust]  
Joined: Sep 2019
Posts: 37
Rev1 Offline
newbie
Rev1  Offline
newbie

Joined: Sep 2019
Posts: 37
Hey dripcan, make sure you check logic voltage. Very important to have 4.8-5.2 vdc. This is extremely crucial with that system. I could see the power supply going slightly out of whack after sitting so long. I have had wierd things like a blank screen happen and found low voltage on the logic end being the issue. If that's not the confirmed issue via voltage check it is okay to initiate the drive versus reinitiating the drive.

#28508 - 12/31/19 01:44 PM Re: miprom21 [Re: DripCan]  
Joined: Jan 2014
Posts: 130
DripCan Offline
member
DripCan  Offline
member

Joined: Jan 2014
Posts: 130
Thanks a lot .did int got car to move on inspection now copying number from other cars.You all have a Happy an Safe New Year see you in 2020 b


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.077s Queries: 15 (0.041s) Memory: 2.6770 MB (Peak: 2.8387 MB) Zlib disabled. Server Time: 2024-03-29 09:20:40 UTC