Who's Online Now
0 registered members (), 7 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,466
Posts36,641
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#29985 - 10/01/20 11:43 AM Tac 20 door not opening  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I have a Tac 20 that was shut down and my door linkage was loose. I tightened it up then the next day it shut down again. Now it answers calls and the door will not open.

#29986 - 10/01/20 12:51 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
After main power reset it will open but motor sounds grindy. When manually trying to open and close from the door controller it works but the motor feels rough. Maybe my door motor is bad from the ooose linkage

#29992 - 10/01/20 10:48 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
It is possible the door board is making it sound like that but definitely start with the motor.

#29994 - 10/02/20 12:48 AM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2010
Posts: 566
elmcannic Offline
addict
elmcannic  Offline
addict

Joined: Dec 2010
Posts: 566
S. Central Utah
Have you checked the motor brushes?

#29995 - 10/02/20 12:49 AM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Thanks dirt. I ordered the motor to start. If it is the board is it a drop in replacement? I can do a door scan with just ims No lon cables? My IMS Version is probable old Is that a problem ?

#29996 - 10/02/20 12:50 AM Re: Tac 20 door not opening [Re: elmcannic]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Yes checked motor brushes. Looks good

#29997 - 10/02/20 03:32 AM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Apr 2020
Posts: 389
Montana Offline
enthusiast
Montana  Offline
enthusiast

Joined: Apr 2020
Posts: 389
Is it the motor grinding or could it be a bad bearing on your idler sheave allowing the side of aluminum sheave to rub/grind. Did you get your linkage back where it is suppose to be with your dol and dcl coming in good. What faults are you getting in IMS? Maybe a bad bushing in your linkage. Might have to do a new door scan? Just some thoughts buddy. Keep us posted.

#29999 - 10/02/20 06:39 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
Those are all good suggestions too. Assuming you do have it narrowed down to the motor making grinding sounds while running from the manual buttons, I think the motor is the right move. When I order a door motor I usually pick the part number that comes with the encoder. There’s a separate number for the bare motor, the motor with the big optical encoder for the PY and older boards and one for the motor with the small digital encoder for the PA boards. Which encoder will also answer your other question about replacing the board. Big encoder = order a PY3 board and you can just drop it in and do a scan from IMS. Small encoder = order a PA6 board and a 6300HL1 UIT if you don’t already have one. The PA boards need a preset profile loaded and the easiest way to do that is using the Config menu with the UIT. Then you can do a scan and adjust from IMS. Of course you can also do all that from the UIT too.

#30001 - 10/02/20 10:36 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2009
Posts: 533
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 533
That UIT with the extension cable is the trick.....Lot better than hooking up IMS to the door operator or controller.

#30003 - 10/02/20 10:50 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
Oh ya the ribbon cable part number is 9863295. Makes it a little easier. And that’s 6300HL1 for the UIT.

#30005 - 10/03/20 01:00 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I have an encoder. Not sure if it’s the big one or small one. I think this is an older Tac 20. Very Early 2000s. Has pump motor under tank . I gave vertical express job number and picture of the door motor. They gave me confirm for part number 9841775. Optical sensor and door motor. 529$ each. I don’t have the UIT. I should get one anyway. There was a flood in the building 2 years ago and tyssen replaced all the boards in shaftway. I hope they didn’t upgrade and vertical express has no clue

Last edited by Jluff; 10/03/20 01:10 PM.
#30007 - 10/03/20 02:46 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
I’m sure they didn’t but it wouldn’t hurt to have the UIT on hand for the future. It’s literally just a generic LCD screen with 4 buttons on a board. I doubt VE charges that much for them but who knows.

#30009 - 10/03/20 09:15 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2009
Posts: 533
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 533
$207 for uit--27 for cable and worth every penny. Get a hard case, put some foam in inside it and keep that in your truck.

So much easier than hooking up IMS

#30011 - 10/04/20 02:51 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
It fits great in this little Otter Box

UIT Box

#30012 - 10/04/20 10:37 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2009
Posts: 533
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 533
That looks sweet. I like how you put the access for the ribbon cable.

#30021 - 10/06/20 03:13 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Vertical express sent me the motor with the big optical encoder. I have the small encoder with a 6300 PA6 2918 rev W board. This motor will not work with this board correct ?

#30022 - 10/06/20 06:00 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Vertical express is telling me the cat number on the motor I have pulls up the one with big optical sensor. I told them I have a PA6 board and they are confused lol

#30023 - 10/06/20 07:59 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
I don’t think the part number on the motor is different depending on which encoder originally came with it but maybe there is and it originally came with the other encoder.
No, that encoder will not work with a PA6. The Motor/encoder you need is 9779504. The encoder part number is 9825431

#30024 - 10/06/20 09:10 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Thanks dirt. They are sending the correct motor/encoder combo . I guess vertical express had a cyber attack 6 weeks ago and they can’t look into a lot of job files. Supposedly they are still working on recovering from this hack. Pretty crazy.

Last edited by Jluff; 10/06/20 09:30 PM.
#30025 - 10/06/20 10:47 PM Re: Tac 20 door not opening [Re: Jluff]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
That was all of ThyssenKrupp


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.043s Queries: 15 (0.013s) Memory: 2.7974 MB (Peak: 3.0736 MB) Zlib disabled. Server Time: 2024-03-28 12:00:33 UTC