Who's Online Now
0 registered members (), 12 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
Page 2 of 2 1 2
#31515 - 07/30/21 11:37 AM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
It seems the problem is my jack low pressure switch .. I wonder if my up leveling strainer is causing this.

Last edited by Jluff; 07/30/21 11:44 AM.
#31521 - 07/31/21 03:08 PM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Update. Every time car gets sunk in pit i get 24v to prsw . Causing shutdown. Car still levels fine after sync and shuts down level at bottom terminal landing... car passes standing test ...There is no visible leaks anywhere. System is dry .. my car is not bottoming out .. has anybody else had this problem ?

Last edited by Jluff; 07/31/21 03:23 PM.
#31522 - 07/31/21 10:46 PM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Mar 2014
Posts: 212
Silly Offline
enthusiast
Silly  Offline
enthusiast

Joined: Mar 2014
Posts: 212
Depending on software, older versions would spit the 1074 out, as a proper resync does allow PRSW to come active. IDWT has the right idea, do a FJR on a clean slate and see what faults pop up. The 1074 could just be a ghost, and not part of your problems. While resyncing, verify you do not come off NTSB or DLT. That's where my money is right now, as while syncing, you lose placement, car won't make an effort to "find" itself, but on a power cycle it will...

As for the original door issue, potentially car could have been racking during the resync, allowing a car door or hoistway door to open, causing that original 1110. Again easy to duplicate by using the FJR.

#31523 - 08/01/21 10:04 AM Re: Tac 32. Fault 1110 [Re: Silly]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Did a FJR and got 1074 and 1110 .. also turned power off and manually lowered car into pit. Turned power on and got same results. 1074 and 1110 as car leveled up out of pit. With prsw jumped out it does not give me any faults during resync forced or manually lowered

Last edited by Jluff; 08/01/21 10:06 AM.
#31525 - 08/02/21 12:26 AM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
You do have BLO in your IO map right? It should be port 8 bit 2.

#31526 - 08/02/21 10:11 AM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
No. BLO not there under port 8

#31530 - 08/02/21 08:51 PM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Add it

#31531 - 08/02/21 11:54 PM Re: Tac 32. Fault 1110 [Re: Indirtwetrust]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Ok. Thanks dirt. I wonder how this car ran for a year with no shutdowns

#31533 - 08/03/21 10:57 PM Re: Tac 32. Fault 1110 [Re: Jluff]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
It shouldn’t need it since it’s not actually doing anything but I found an old note that this fixed some odd syncing problems. It’s possible this was fixed with a software update too. What version is the software?

Page 2 of 2 1 2

Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.110s Queries: 16 (0.071s) Memory: 2.7168 MB (Peak: 2.9119 MB) Zlib disabled. Server Time: 2024-03-29 07:41:45 UTC