Who's Online Now
1 registered members (wltr00), 13 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#34185 - 11/07/22 04:42 PM Gen 2 door operator  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Hello. I’m working on Gen 2 Front and rear doors. Linear operators. Belt was broke on rear doors. Replaced belt and realized doors were shutdown.plugged Service tool into door operator. Says SHD DED. the only input high is LOS .. there were faults in the log but I cleared them to quickly to make note of them. LEDs seem ok. Green blinking. Red steady. Yellow led came on after playing with buttons on top Anybody have info on these operators? Power coming in is good. 240v

Last edited by Jluff; 11/07/22 04:44 PM.
#34187 - 11/07/22 05:38 PM Re: Gen 2 door operator [Re: Jluff]  
Joined: Jan 2019
Posts: 80
M2RE Offline
Chilling
M2RE  Offline
Chilling

Joined: Jan 2019
Posts: 80
After replacing the belts, did you learned the travel?

#34188 - 11/07/22 06:00 PM Re: Gen 2 door operator [Re: M2RE]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
No. I saw that it said SHD DED. And I stopped there. I need info on how to work on these doors . Do you have run learn procedures? Is that normal occurrence after losing belt? I have replaced these belts b4 with out any other issues . There is no power on the doors. Have to close by hand to move the car. This is a glide operator

Last edited by Jluff; 11/07/22 06:10 PM.
#34189 - 11/07/22 06:41 PM Re: Gen 2 door operator [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
I have a manual I found from Unitec. I will be back tomorrow.

#34194 - 11/08/22 02:42 PM Re: Gen 2 door operator [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
All my board functions and power check out good. My status lights all are acting as they should . 240v to P1. No P3 connection. P4 pin 1 to 3 has proper voltage. 24v discrete input. My DCP voltage is correct. 24v when away from sensor. 0 v when on sensor. I can see values change on my service tool as I move door by hand. Service tool plugged into door board says SHD DED. I never get any voltage to my 3 wire motor connector. But I never get the board to say ready. As soon as I do a learn run from the buttons on top of door board it aborts the learn .

#34196 - 11/09/22 03:04 AM Re: Gen 2 door operator [Re: Jluff]  
Joined: Dec 2011
Posts: 259
beaupeep Offline
Mechanic
beaupeep  Offline
Mechanic

Joined: Dec 2011
Posts: 259
ontario
Is it an at400

#34197 - 11/09/22 09:59 AM Re: Gen 2 door operator [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Glide

#34198 - 11/09/22 02:57 PM Re: Gen 2 door operator [Re: Jluff]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
A learn travel solved this problem. After repeated attempts lol

#34201 - 11/09/22 05:43 PM Re: Gen 2 door operator [Re: Jluff]  
Joined: Jan 2019
Posts: 80
M2RE Offline
Chilling
M2RE  Offline
Chilling

Joined: Jan 2019
Posts: 80
Awesome


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.043s Queries: 15 (0.010s) Memory: 2.7086 MB (Peak: 2.9025 MB) Zlib disabled. Server Time: 2024-03-29 13:02:04 UTC