0 registered members (),
11
guests, and
3
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums13
Topics6,515
Posts36,880
Members8,461
|
Most Online117 Jan 16th, 2020
|
|
|
#11012 - 06/14/14 11:37 PM
TAC50-03 door board short version
|
Joined: Mar 2012
Posts: 102
Elevatorfella
member
|
member
Joined: Mar 2012
Posts: 102
|
Sorry about the long winded post earlier, Long days this week. 1) replacing a 6300PA2 with a 6300 PA7. 2) center opening doors, what is jumper configuration. J1-J8? 3) how Do I perform a learn cycle using IMS? 4) installed new door board, motor is running backwards, when using open and closed on board. 5) door op. Is on the left side when looking outside from top of car.
Thanks for any help
Last edited by Elevatorfella; 06/14/14 11:41 PM.
|
|
|
#11014 - 06/15/14 01:25 AM
Re: TAC50-03 door board short version
[Re: Elevatorfella]
|
Joined: Jan 2014
Posts: 130
DripCan
member
|
member
Joined: Jan 2014
Posts: 130
|
try removing jumper three for motor reversal if not three then two i had wrong direction a while back but cant recall for sure.if jumper already off put on then
Last edited by DripCan; 06/15/14 01:30 AM.
|
|
|
#11020 - 06/15/14 10:15 PM
Re: TAC50-03 door board short version
[Re: DripCan]
|
Joined: Sep 2012
Posts: 451
sbrmilitia
addict
|
addict
Joined: Sep 2012
Posts: 451
|
Jp1 1 to 2 JP2 2 to 3 Jp3 off Jp4 off for front on for rear Jp5 installed for 486 off for can Jp6 off
I pulled the wrong book that's for 6300paxx on a 04 I'll have to get the 03 book in the morning.
Last edited by sbrmilitia; 06/15/14 10:18 PM.
|
|
|
#11026 - 06/16/14 01:05 PM
Re: TAC50-03 door board short version
[Re: sbrmilitia]
|
Joined: Mar 2014
Posts: 212
Silly
enthusiast
|
enthusiast
Joined: Mar 2014
Posts: 212
|
I know jp7-8 were both resistors on the old card. We remove them for CAN communication, they were left on for LON, so if the 50-03 is LON based they should remain. Direction of doors is handled in door smarfast, believe it is under the sub heading of door. Verify that the hand of door matches, dc motor, linear operator, etc.
The door scan is also in door smarfast, think in IMS it is service, door diagnostics, door smart fast to open. First screen there is a commands prompt, drop down arrow, first command is auto null, drop down and there is learn travel.
I will be on the ground in another 4-6 hours, if you need more help I will fire the laptop up at the hotel.
|
|
|
|
|