Hi Guys:
I have this sigma controller fault, but do not have the manual.
The screen show:
ACD=03 07FL 042%
E085-91 000000 S
1100110100000010
Anybody know what it is? and how to reset it?
Also, anybody have a sigma controller manual? I would like to
Purchase from him?
my email is kenelev@hotmail.com
Thanks,
Ken

ACD 03 = out of service
07FL = the elevator is in the 7 floor
042% = is the value of the load weight inside the cab
E085 = check the relay R5SC auxiliar contacts stay on

I'm a certified LG/Sigma elevator technician, if you have any other problem feel free to contact.

Thanks,
I will check it out tomorrow.

Hi zab
R5SC is not picking up but the safety circuit ring out good?
I have 50 vdc all the way to pit-2 terminal?
On DOR-210 BOARD which terminal is for R5SC relay?
Thanks,
Ken

Hello, maybe you need to make a learn, I have 6 units a there's no problems. How many floors does the building have?

7 stops and no manual
Can anybody sell me a copy of the manual?
Thanks,
Ken

Ken, send me your email . I have the information you need.

Email
Kenelev@hotmail.com
Thank you

Ok Ken , I send you the information.

Thanks,
I will check it out tomorrow.
Ken

Update:
First, Thank You guys for all the help!

Finally, get the elevator going.
Problem is DOR-220 board OUT-1 connector (Bad Connection).
Even fix the connection, the fault E085 still stay and R5SC relay still not picking up.
Need to turn off mainline, set DOC-220 board SW5 dip switch 4 on, then turn on mainline, then the R5SC relay pickup and the fault E085 go away.
Don't know it is the right thing to do. Still looking for a manual.
One thing I do learn from this call is. It is close to impossible to troubleshoot this controller without the right print and manual, most of all you guys help!
Ken :-)

Hi All
I have Sigma control , any one can help me I do not have the manual ,
how can I use DOA-100 ???
Thanks

Hi Cucuvator

I do appreciate if you can send me an copy of user manual DOA-100
(in English) my email : lifts012@gmail.com

Hey, tell the problem, I try to find the best answer, I don't have the manual in Pdf.

have you solved this problem already?
if still no, please let me know

Not really off topic, but I think it's great to see the forum reaching across the globe. Experience from distant places from "home" blazing across the internet bringing help to whomever needs it on a variety of equipment.
Thanks everyone for your input over the years, it great to see!

E85 this mean R5SC always on , you can solve by checking 48 volt , and input output buffer of R5SC , some time feed back ground appear as 48 volt , ground source from main boared DOC ..

Hi
My lift is showing error 55-94 it bombs out as soon as relay C1ST and C2ST attempt to pull in.
it does not move at all.

Hi
I have a Sigma Si210 having an error E095-91 wich randomly appears.
making some research i have found is a r5sx related failure, still need the manuals, does somebody have these manuals in PDF?

Dear aLL;
we have 2 sigma elevators, one is not working for so long,we are trying to solve the problem, it gives us
so many error codes( E171-90 000 00s,E053-91, E032-91), and we don't have the manual, I am wondering if you guys can help us. I am also looking for some one who can travel to addis ababa, ethiopia to fix our elevator, one with a good knowledge of fixing elevator
best regards
Fikadu
+251-911-175303

E171: usual synchronous position error. To prevent such problem as door zone not detected because of non-corresponding synchronous position by rotary encoder
E32: INV U-phase IGBT Error( 180-420m/min). When U-phase +IGBT and -IGBT are turned on simultaneously, or when IGBT driving
power has failed or INV output(U, V, W) is short
E53: INV Charge Error

Dear Kenelev;
thank you I really appreciate your help, infact am looking for some to come to ethiopia( east africa), and help me to fix the elevator. Do you think you can help me?, my email: fikepk12@gmail.com or fikekifay@helzerinn.com my number:+251911-175303
best regards
Fikadu

Please I need manual for sigma elevator

Sorry fikir123, ethiopia is a bit too far form me.
And I don't have the complete manual either only the fault chart.
But by looking @ the faults. Look like u have the dive problem.
IGBT may be shorting out. Send out the drive to have it check out.

Thanks for your help Kenelev,i really appreciate, but do you know anyone who can come and fix it for us( a good elevator technician) and if you dont mind, can you send me the fault chart?, thank you once again.
best regards
Fikadu

check your PM

Dear Kenelev;
thanks...there is nothing in my PM
regards
Fikadu

Sorry, I mean email.

Dear Kenelev;
there is nothing in my email as well
fikadu

re-send again. Check your spam also.

Thanks ken, got it

Hi, this is great forum and very helpful , kenelev could you please send me the sigma manual, dionil_ayala@hotmail.com

Hi. Can you help me for ereor 069

Hi Rosman:
I cannot find fault code 069. According to my fault 069 is not being use.
Is any other fault code show up?

Hi Dipi:
I do not have the manual, only fault chart.
What fault it showing? and what seem to be the problem?

Hi

I have a problem with the IGBT, i have been replaced with new igbt but the same problem also occurs namely U phase problem first error is E035 after reset the controller error is E032-91 anyone can help me
Thanks

u may have problem with the DPP board.
pm your email.

Dear
kenelev
My email: miskan.asiafuji@gmail.com

email send

Thanks for your help Kenelev

Hello kenelev
Can you help me for ereor 096

Hello kenelev,
Can you help me for ereor 096

Hello kenelev,
Can you help me for ereor 096

email send
Good luck

Dear kenelev,
I have a trouble with my sigma elevator, it's E088-91 on the keypad. What is that mean, n what should i do?
Here's my email : bahtiarhandoko@gmail.com

Dear All;
I have 2 sigma elevators, one is working the other one is not.
I want an engineer who can come to Ethiopia and fix it for us.
We will cover all his expenses( visa, air ticket, accommodation). and we can give him pocket money as well
Any one who is interested and have good knowledge on sigma elevator, Please contact me,
e-mail: fikepk12@gmail.com
Tel: +251911175303
whats app: +251911175303

hi i have doa-100
code error is 99: DUAL INPUT SIGNAL TROUBLE
i don't understand this problem????
whatsapp: +212661115891
thinks

I have a OTIS SIGMA with the E124. I did the procedure to reset it: A43E
Everything is dead in the car, no position indicator inside the car or outside the car.
Car is leveled on the top floor.
I tried a to do a FHM but the controller status ADC = 03 is not changing to ACD = 09
When I press 3, it does not move.
My SW4 Switch is set correctly
My Safety Circuit is good, the R5SX relay is IN but not the R5SC.
Any help ?

Dear kenelev
I have problem in sigma elevator
I can't use svc tool when i enter any order
Ex A13E
he give me mseg ACCESS DENIED
he worked only on code A42E
Can you help me solve my problem
Thanks for you

Hi all
I have problem in sigma elevator
I can't use svc tool when i enter any order
Ex A13E
he give me mseg DENIED
he worked only on code A42E
Can you help me solve my problem
Thanks for you

Hi sir do you have manual about LG lvp elevator sir?

Sir do you have manual of lg lvp elevator

Hi Guys:

I have this sigma DGS-700 controller fault, but do not have the manual.
The screen show:
ACD=03 08FL 000%
E016-91 000000 S

Anybody know what it is?
and how to reset it?
Also, anybody have a sigma controller manual?

my email is jol.valera.r@gmail.com
Thanks,

Hi sir, are you still available to help?