Who's Online Now
0 registered members (), 7 guests, and 1 spider.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,643
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#21137 - 07/15/17 03:07 PM US assension 1000  
Joined: Sep 2015
Posts: 61
TCElevator Offline
journeyman
TCElevator  Offline
journeyman

Joined: Sep 2015
Posts: 61
Will not hold hall call or car calls
Will not run up on ins or down
Sarter says motor wiring fault (siemens soft start)
Car was running for years just fine
Put on insp - took off insp. ran up didnt open doors
And now we are dead in the water
Checked just about everything possible but dont
know about the boards? Does anyone have info on tool
or backround on the boards

#21138 - 07/15/17 03:42 PM Re: US assension 1000 [Re: TCElevator]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
Any Electical work done in building? Maybe phase reversal on main lines?

#21139 - 07/15/17 03:56 PM Re: US assension 1000 [Re: Rolly]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
What does the starter say now? The way the Siemens starter was wired in is kind of a wild card. Most common reason for the motor wiring fault display is the fault contactor not picking.

In general with Ascension 1000's strange behavior tends to root in the power supply or it's connections. Make sure your power supply is like 5.1 vdc and the connections are good. All the smiled plugs can cause problems as well as the card plugs.

#21143 - 07/15/17 06:27 PM Re: US assension 1000 [Re: Indirtwetrust]  
Joined: Sep 2015
Posts: 61
TCElevator Offline
journeyman
TCElevator  Offline
journeyman

Joined: Sep 2015
Posts: 61
4.7 on most of the 5v areas

#21145 - 07/15/17 07:23 PM Re: US assension 1000 [Re: TCElevator]  
Joined: Sep 2015
Posts: 61
TCElevator Offline
journeyman
TCElevator  Offline
journeyman

Joined: Sep 2015
Posts: 61
Starter says motor wiring fault only if you enter into menu and find faults on main screen just motor stoped
Fault contactor stays pulled in constant

#21147 - 07/15/17 08:40 PM Re: US assension 1000 [Re: TCElevator]  
Joined: May 2013
Posts: 224
Jcjmowrey Offline
enthusiast
Jcjmowrey  Offline
enthusiast

Joined: May 2013
Posts: 224
Atlanta ga
Like indirt said, adjust your 4.7 up to 5.1 before you go any further. I recently had a 1000 doing some funny door stuff and when I plugged my tool into it, everything went haywire. Voltage was 4.8 and when I brought it up to 5.1 all door issues went away and I could plug into it fine.


If all else fails, read the instructions
#21148 - 07/16/17 03:56 PM Re: US assension 1000 [Re: Jcjmowrey]  
Joined: Sep 2015
Posts: 61
TCElevator Offline
journeyman
TCElevator  Offline
journeyman

Joined: Sep 2015
Posts: 61
Do you use the world tool ?
Does anyone have feedback on tools

#21149 - 07/16/17 04:46 PM Re: US assension 1000 [Re: TCElevator]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
I would go for the world tool before they only sell it on a tablet or something. I've never used the World version but it looks to be a copy of the original PCD that I have. The company I work for has a PC based tool also that works for the 2000 too, the nice thing about that is when you change displays, it changes the labels of the bits to match so you don't have to refer back and forth to a book. I made overlays for the different displays for that reason but don't use them as much as I thought I would.

Whether or not that tool works for Ascension 200 or not might be an important consideration for which tool you go with though.

#21150 - 07/16/17 08:44 PM Re: US assension 1000 [Re: Indirtwetrust]  
Joined: May 2013
Posts: 224
Jcjmowrey Offline
enthusiast
Jcjmowrey  Offline
enthusiast

Joined: May 2013
Posts: 224
Atlanta ga
I have the world tool and it does change the labels. The only issue with their tool is the timing. You can tell that your working on a new laptop that's plug into an old microprocessor(I guess that's a good way to describe it). When you change displays you have to wait for the software to catch up. And when your moving through groups and bits you have to get your timing right to get the "focus" where you want it to make adjustments, but once you've done it a couple of times it's fairly simple.


If all else fails, read the instructions
#21151 - 07/16/17 09:53 PM Re: US assension 1000 [Re: Jcjmowrey]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
Is that the one that looks like the original PCD or the PC version?

#21152 - 07/16/17 11:13 PM Re: US assension 1000 [Re: Indirtwetrust]  
Joined: May 2013
Posts: 224
Jcjmowrey Offline
enthusiast
Jcjmowrey  Offline
enthusiast

Joined: May 2013
Posts: 224
Atlanta ga
Pc version


If all else fails, read the instructions
#21153 - 07/17/17 01:02 AM Re: US assension 1000 [Re: Jcjmowrey]  
Joined: Dec 2010
Posts: 566
elmcannic Offline
addict
elmcannic  Offline
addict

Joined: Dec 2010
Posts: 566
S. Central Utah
With the multiple symptoms described, I'd say Dirt hit it on the head...5volt supply.
Those connectors are notorious for intermittent weired troubles. We soldered them and (if memory serves me right) also ran a wire direct from that supply (5v) to the 5volt terminal location up top on the controller terminal strip.

#21155 - 07/17/17 03:22 AM Re: US assension 1000 [Re: elmcannic]  
Joined: May 2011
Posts: 487
E-man Offline
addict
E-man  Offline
addict

Joined: May 2011
Posts: 487
I've had to jack the 5v up to 5.4 before the car would run.

#21157 - 07/17/17 05:06 PM Re: US assension 1000 [Re: E-man]  
Joined: Sep 2015
Posts: 61
TCElevator Offline
journeyman
TCElevator  Offline
journeyman

Joined: Sep 2015
Posts: 61
Sounds like a plan and does anyone have access to an extra pcd?

#21159 - 07/18/17 11:00 AM Re: US assension 1000 [Re: TCElevator]  
Joined: Jan 2010
Posts: 662
danzeitz Offline
addict
danzeitz  Offline
addict

Joined: Jan 2010
Posts: 662
st.louis mo
We would get rid of all the factory female push on connectors and replace them with single small female stacons. And this would end the problem with high resistance causing your 5VDC to drop. We would mark the factory white wires with black dots so you could know where they went.

#21169 - 07/18/17 10:55 PM Re: US assension 1000 [Re: danzeitz]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
I replace the original Molex terminals with gold plated Trifurcon type. No more issues and you can still use the Molex plug housing. Just need to invest in a set of crumpets.


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.055s Queries: 15 (0.024s) Memory: 2.7652 MB (Peak: 3.0165 MB) Zlib disabled. Server Time: 2024-03-28 14:40:38 UTC