Who's Online Now
0 registered members (), 12 guests, and 1 spider.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,644
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#22064 - 10/31/17 07:28 PM Swift 5000 Communication  
Joined: Jan 2011
Posts: 119
sccjr Offline
Shootintrouble
sccjr  Offline
Shootintrouble

Joined: Jan 2011
Posts: 119
Need some help here fellas. Can you communicate with a swift 5000 via hyperterminal and if so whats the proper procedure? Thanks.

#22070 - 10/31/17 10:36 PM Re: Swift 5000 Communication [Re: sccjr]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
Yes, 1200, 8, N, 1.

#22072 - 11/01/17 12:37 AM Re: Swift 5000 Communication [Re: Rolly]  
Joined: Jan 2011
Posts: 119
sccjr Offline
Shootintrouble
sccjr  Offline
Shootintrouble

Joined: Jan 2011
Posts: 119
Got a 5000 tripping out with a 23, 24 flt only in the down direction, different spots in the h/w. Travel demand is 500fpm actual 497. DAR, REG Boards have been replaced with boards from running car in the same group. TAC & TAC cable have been replaced. Pwr supplies good with no AC ripple.Any ideas?

#22074 - 11/01/17 03:56 AM Re: Swift 5000 Communication [Re: sccjr]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
which fault comes first?

#22075 - 11/01/17 03:58 AM Re: Swift 5000 Communication [Re: Rolly]  
Joined: Jan 2011
Posts: 119
sccjr Offline
Shootintrouble
sccjr  Offline
Shootintrouble

Joined: Jan 2011
Posts: 119
23

#22076 - 11/01/17 11:20 AM Re: Swift 5000 Communication [Re: sccjr]  
Joined: May 2013
Posts: 224
Jcjmowrey Offline
enthusiast
Jcjmowrey  Offline
enthusiast

Joined: May 2013
Posts: 224
Atlanta ga
Magnetek drive? How close is your tach cable conduit run to high voltage wires? Are there big ass radio,microwave, cell tower, etc stuff on the roof of the machine room?


If all else fails, read the instructions
#22078 - 11/01/17 11:39 AM Re: Swift 5000 Communication [Re: Jcjmowrey]  
Joined: Jan 2011
Posts: 119
sccjr Offline
Shootintrouble
sccjr  Offline
Shootintrouble

Joined: Jan 2011
Posts: 119
MG. I pulled a new tach cable outside of the piping and shortened it as much as I could. No tower interferences.

#22080 - 11/01/17 12:50 PM Re: Swift 5000 Communication [Re: sccjr]  
Joined: Aug 2016
Posts: 732
Jluff Offline
old hand
Jluff  Offline
old hand

Joined: Aug 2016
Posts: 732
Check the SCRs

#22094 - 11/02/17 01:33 AM Re: Swift 5000 Communication [Re: Jluff]  
Joined: Jan 2011
Posts: 119
sccjr Offline
Shootintrouble
sccjr  Offline
Shootintrouble

Joined: Jan 2011
Posts: 119
Got it. I tweaked on the F pot on the DAR board. Been running with no faults for 8 hours. Thanks for all the help.

#22673 - 01/09/18 01:30 AM Re: Swift 5000 Communication [Re: sccjr]  
Joined: Aug 2013
Posts: 35
MILTRONICS Offline
newbie
MILTRONICS  Offline
newbie

Joined: Aug 2013
Posts: 35
For all your CEC Swift Questions and concerns,

call Issa @ 917-417-7389

or email him @ Issa@elevatorboards.com


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.027s Queries: 15 (0.007s) Memory: 2.7149 MB (Peak: 2.9152 MB) Zlib disabled. Server Time: 2024-03-28 15:55:32 UTC