Who's Online Now
1 registered members (Indirtwetrust), 14 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,653
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#22822 - 01/23/18 06:16 PM Kone kcm831 with v3f25s drive. E-brake pick issue  
Joined: Jan 2015
Posts: 17
mikecoavs Offline
stranger
mikecoavs  Offline
stranger

Joined: Jan 2015
Posts: 17
Denver, CO
Hello everyone. Another Kone question. I have a unit that is slow to pick up the e brake causing intermittent issues on takeoff. For now I'll leave the faults out of it as I believe they are standard if the brake doesn't pick. On the adon 2 I get my e brake command from cpu as well as k464 relays on, but e brake command(adon) doesn't come on right away like it should. Which is the power for the brake module to pick the brake. This is consistent for each run as well as on inspection while pressing just a direction to pick the e brake only. I have swapped the adon out. Swapped brake modules just in case and no change. So far the only thing I have found is incoming power pushing 500vac while my transformer is for 480vac. Pushing all my voltages on the lce-rec high. Unable to change at this time( no taps). Any ideas are appreciated. Possible cpu change out? Not wanted due to older So I and would to be upgraded to the kcp version. Thanks Mike

#22839 - 01/25/18 04:14 PM Re: Kone kcm831 with v3f25s drive. E-brake pick issue [Re: mikecoavs]  
Joined: Jun 2017
Posts: 36
Norcan Offline
newbie
Norcan  Offline
newbie

Joined: Jun 2017
Posts: 36
I would go over the e brake itself. Check for proper gaps. Possible mechanical binding of the brake. Center washer should have play in it. Brake micro is picking up properly and dropping out properly.

#22840 - 01/25/18 05:03 PM Re: Kone kcm831 with v3f25s drive. E-brake pick issue [Re: mikecoavs]  
Joined: Feb 2013
Posts: 757
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 757
ohio
swap the main and e-brake modules, and see if the problem is the module itself.

#22841 - 01/25/18 05:05 PM Re: Kone kcm831 with v3f25s drive. E-brake pick issue [Re: mikecoavs]  
Joined: Jan 2015
Posts: 17
mikecoavs Offline
stranger
mikecoavs  Offline
stranger

Joined: Jan 2015
Posts: 17
Denver, CO
Thanks for the reply Nor can. Physically and electrically the e brake is picking like it should. It's the actual command from the adon board into the brake module that is getting delayed by a half second. Which in realtime causes the main brake to be picked a hair before the emergency.

#22842 - 01/25/18 05:06 PM Re: Kone kcm831 with v3f25s drive. E-brake pick issue [Re: mikecoavs]  
Joined: Jan 2015
Posts: 17
mikecoavs Offline
stranger
mikecoavs  Offline
stranger

Joined: Jan 2015
Posts: 17
Denver, CO
Hi John. I did already try that and the same issue occurs. Thanks for the idea though

#22843 - 01/25/18 06:38 PM Re: Kone kcm831 with v3f25s drive. E-brake pick issue [Re: mikecoavs]  
Joined: Feb 2013
Posts: 757
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 757
ohio
Have you checked the voltages at the cable XD1 and XD2 where they go into the E Brake Module at XB1 and XB2? Or checked the ribbon cable for continuity.

#22844 - 01/25/18 06:40 PM Re: Kone kcm831 with v3f25s drive. E-brake pick issue [Re: mikecoavs]  
Joined: Feb 2013
Posts: 757
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 757
ohio
Also the XB2 and the XEB2 Ribbons.


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.039s Queries: 14 (0.009s) Memory: 2.6933 MB (Peak: 2.8664 MB) Zlib disabled. Server Time: 2024-03-28 23:45:23 UTC