Who's Online Now
1 registered members (Indirtwetrust), 11 guests, and 3 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,648
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#23696 - 04/05/18 07:55 PM Otis 311  
Joined: Jun 2014
Posts: 33
Greg1234 Offline
Slayer
Greg1234  Offline
Slayer

Joined: Jun 2014
Posts: 33
Having a leveling issue, some floors are perfect while others are off a quarter inch.No reason for vanes to have moved.Wont recognize learn trip.

#23700 - 04/06/18 01:17 AM Re: Otis 311 [Re: Greg1234]  
Joined: Jul 2013
Posts: 198
NewMech Offline
member
NewMech  Offline
member

Joined: Jul 2013
Posts: 198
What do you mean by won't recognize?

#23704 - 04/06/18 01:44 PM Re: Otis 311 [Re: Greg1234]  
Joined: Jun 2014
Posts: 33
Greg1234 Offline
Slayer
Greg1234  Offline
Slayer

Joined: Jun 2014
Posts: 33
Tool says abort , car stops before reaching the needed 0 value at the bottom landing to initialize learn run.


Slayer
#23707 - 04/06/18 09:59 PM Re: Otis 311 [Re: Greg1234]  
Joined: Jul 2011
Posts: 16
hotsauce04 Offline
stranger
hotsauce04  Offline
stranger

Joined: Jul 2011
Posts: 16
Try replacing your batt ram chips if it wont take learn run

Last edited by hotsauce04; 04/06/18 10:00 PM.
#23708 - 04/06/18 10:30 PM Re: Otis 311 [Re: Greg1234]  
Joined: Apr 2018
Posts: 5
Elev8d Offline
stranger
Elev8d  Offline
stranger

Joined: Apr 2018
Posts: 5
Bump up ntsd tolerance to about 500 and try it. Then set it back.

#23712 - 04/07/18 03:13 PM Re: Otis 311 [Re: hotsauce04]  
Joined: Dec 2015
Posts: 1,528
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,528
Local 18
Originally Posted by hotsauce04
Try replacing your batt ram chips if it wont take learn run



When those Dallas RAM chips have been the issue, it has worked for me to just swap the 2. They aren’t bad, just like glitched. Of course I don’t know if this always works.

#23713 - 04/07/18 03:57 PM Re: Otis 311 [Re: Greg1234]  
Joined: Feb 2015
Posts: 43
TNHapa84 Offline
newbie
TNHapa84  Offline
newbie

Joined: Feb 2015
Posts: 43
Check and make sure your sensors are clean and dont have hoistway junk and dust. run the car down an inspection and make sure NTB goes lower case IN (menu or module ) M 2-1-3-1 i think then make sure ET1.

#23715 - 04/07/18 05:05 PM Re: Otis 311 [Re: Greg1234]  
Joined: Jun 2014
Posts: 33
Greg1234 Offline
Slayer
Greg1234  Offline
Slayer

Joined: Jun 2014
Posts: 33
Hey guys I really appreciate the help, I will hopefully get it fixed and will reply back with what the issue was, thx a million!


Slayer
#23720 - 04/07/18 10:40 PM Re: Otis 311 [Re: Greg1234]  
Joined: Jul 2013
Posts: 198
NewMech Offline
member
NewMech  Offline
member

Joined: Jul 2013
Posts: 198
Only one batram chip is really used, the other is backup. You are leaving the bad one in the backup socket on the board.

#23721 - 04/07/18 10:43 PM Re: Otis 311 [Re: Greg1234]  
Joined: Jul 2013
Posts: 198
NewMech Offline
member
NewMech  Offline
member

Joined: Jul 2013
Posts: 198
If increasing your NTSD tolerance does the trick, that is a good indicator that your NTSD vane is the wrong length.

#23745 - 04/12/18 01:16 AM Re: Otis 311 [Re: Greg1234]  
Joined: May 2012
Posts: 194
Len Offline
member
Len  Offline
member

Joined: May 2012
Posts: 194
---------worn sheaves on machine and cables will cause cable slippage too much slippage throws the hoistway counts..off

#23784 - 04/17/18 06:31 PM Re: Otis 311 [Re: Greg1234]  
Joined: Jun 2014
Posts: 33
Greg1234 Offline
Slayer
Greg1234  Offline
Slayer

Joined: Jun 2014
Posts: 33
Appreciate all the help guys, Len you where spot on, cables are slipping just enough to cause the count to be off.Thanks for your input!


Slayer

Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.043s Queries: 15 (0.006s) Memory: 2.7321 MB (Peak: 2.9497 MB) Zlib disabled. Server Time: 2024-03-28 19:57:53 UTC