Who's Online Now
1 registered members (Dro), 5 guests, and 1 spider.
Key: Admin, Global Mod, Mod
September
S M T W T F S
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30
Newest Members
Csalazar311, Dro, GenErick, SHIHAB ISMAEL, CBueche
4854 Registered Users
Forum Statistics
Forums13
Topics3,947
Posts24,418
Members4,854
Most Online72
Apr 10th, 2016
Previous Thread
Next Thread
Print Thread
#22521 - 12/18/17 03:18 PM Schindler Idd 330a door operator  
Joined: Apr 2013
Posts: 33
500fpm Offline
Elevator fixit guy
500fpm  Offline
Elevator fixit guy

Joined: Apr 2013
Posts: 33
Does anyone have a manual on the Scinder Idd 32 door operator that is commonly used on a 330a. It is the one that uses the LTI drive. It is showing an error and is running in slow speed all the time also seems to be pulsing slightly. Can the ssm service tool be used with this model?

Last edited by 500fpm; 12/18/17 03:18 PM.
#22768 - 01/17/18 04:55 PM Re: Schindler Idd 330a door operator [Re: 500fpm]  
Joined: May 2017
Posts: 50
Tamperprufe Offline
journeyman
Tamperprufe  Offline
journeyman

Joined: May 2017
Posts: 50
USA
Did you ever resolve your issue if so how?
Also did you ever find a manual on IDD? I do have some info on it
Theres not alot of info out there on that DO as it comes "pre-configured" per job specs. I also have same issue on one now.
I have used the SSM and all parameters appear to still be correct
SSM is giving me fault code "5" which I do not know what it is?

1) "running in slow speed" is synchronization speed
2) put elev on cartop insp. On D.O.do "hard reset" hold down open and close buttons at same time, all 5 leds should flash on and off after doors do learn run "ERR" led should be off.
3) my problem is I can not get doors to do learn run and "ERR" led off, it stays lit

#22790 - 01/18/18 11:11 PM Re: Schindler Idd 330a door operator [Re: 500fpm]  
Joined: Oct 2013
Posts: 69
NOTIME Offline
journeyman
NOTIME  Offline
journeyman

Joined: Oct 2013
Posts: 69

#22831 - 01/25/18 12:23 AM Re: Schindler Idd 330a door operator [Re: 500fpm]  
Joined: Apr 2013
Posts: 33
500fpm Offline
Elevator fixit guy
500fpm  Offline
Elevator fixit guy

Joined: Apr 2013
Posts: 33
I tried resetting the error every way possible. It still runs in slow speed only and slams in the open. We are going to replace the drive assembly.

#22927 - 02/03/18 02:31 AM Re: Schindler Idd 330a door operator [Re: 500fpm]  
Joined: Dec 2011
Posts: 173
beaupeep Offline
Mechanic
beaupeep  Offline
Mechanic

Joined: Dec 2011
Posts: 173
ontario
You might want to take a look at the read switch, if not adjusted correctly, it will never learn a run

#22943 - 02/04/18 04:06 PM Re: Schindler Idd 330a door operator [Re: 500fpm]  
Joined: Feb 2015
Posts: 28
BillS Offline
newbie
BillS  Offline
newbie

Joined: Feb 2015
Posts: 28
I believe ECI in Florida make a direct drop in replacement. Much easier to work with.

321-783-5858

#23764 - 04/14/18 04:59 PM Re: Schindler Idd 330a door operator [Re: Tamperprufe]  
Joined: Apr 2013
Posts: 33
500fpm Offline
Elevator fixit guy
500fpm  Offline
Elevator fixit guy

Joined: Apr 2013
Posts: 33
I ended up replacing it. The drive came programmed from the factory just had to adjust the opening distance with the ssm tool and do a learn. That new one did not come with a motor sheave and the old one was stuck so it took me a few hours to get it off.

#23766 - 04/14/18 07:39 PM Re: Schindler Idd 330a door operator [Re: 500fpm]  
Joined: May 2017
Posts: 50
Tamperprufe Offline
journeyman
Tamperprufe  Offline
journeyman

Joined: May 2017
Posts: 50
USA
yeah sometimes those sheaves don't wanna cooperate...instead of paying 4500 again for another new DO, see if you can get the old one repaired locally or send it off and when ya get it back I now have a tool(above and beyond the SSM) that allows you to set up the DO to match any job software configuration/requirements. PM me if your ever interested.


Photo Gallery
otis fixtures
On sell, KONE traction machine brake, rotor, body
KONE MX10 machine body 1
Baker Iron Works Machine no 3
Another Mystery
THINK I FOUND THE PROBLEM
Is this Payne
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.023s Queries: 14 (0.004s) Memory: 5.0032 MB (Peak: 5.2269 MB) Zlib disabled. Server Time: 2018-09-22 14:54:09 UTC