|
0 registered members (),
12
guests, and
4
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums13
Topics6,515
Posts36,880
Members8,461
|
Most Online117 Jan 16th, 2020
|
|
|
#24294 - 07/11/18 05:21 PM
KCM 831
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
I just had to replace a cpu and adon board ( old one was adon1, new is adon3) damaged by power surge. I’ve done adon learn and car runs on inspection and on auto for 1 run. Then I get 140n’s and 240n’s and I never get a shaft communication LED. I also get the fault for no B30 until I jump 30 to B30. There are no rear doors or rear calls. I’m think one or more lcehas/fcb boards are fried and I’m not ever completing Lon node download properly? I’ve checked all parameters and nothing seems wrong. Parameter 1-24 is set to 0. Is there a communication parameter or something like that I’m missing or is my original theory that the hall network is shot?
If all else fails, read the instructions
|
|
|
#24297 - 07/11/18 06:25 PM
Re: KCM 831
[Re: Jcjmowrey]
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
That’s another thing I forgot to mention, I let the doors do there learn on the first floor, it lets me into 5-2-1, I press accept , Then I turn it to auto and then nothing. Does the lon download have to be completed successfully before it does a shaft setup or vice versa?
If all else fails, read the instructions
|
|
|
#24298 - 07/11/18 07:17 PM
Re: KCM 831
[Re: Jcjmowrey]
|
Joined: Apr 2017
Posts: 96
UpandDown2321
journeyman
|
journeyman
Joined: Apr 2017
Posts: 96
|
Does it try to shaft learn at all? You need to be just below the floor to start. Changing a CPU ive never needed to do a door learn first. A 5 7 1 wouldnt be a bad idea and the shaft communication should come up once the learn is accepted. Earthquake needs to be off as well 1-86. Also is the current number of floors correct if you try to scroll and put in a car call
Last edited by UpandDown2321; 07/11/18 07:19 PM.
|
|
|
#24302 - 07/11/18 09:09 PM
Re: KCM 831
[Re: Jcjmowrey]
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
Doesn’t try at all and it won’t let me scroll at all to put in call from cpu. I’ve done 5 7 1 many times. Earthquake is off. And I’ve tried shaft learn exactly like you say, e-man, multiple times. I’ve tried 5 7 2 as well.
If all else fails, read the instructions
|
|
|
#24308 - 07/12/18 01:40 AM
Re: KCM 831
[Re: Jcjmowrey]
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
Yes drive ok is on. It’s funny that there’s no shaft comm on but it won’t let me do a shaft learn but it will level into floor, I can cycle disconnect when it’s at floor level, it will take car calls and go where it’s supposed to(then fault out), and it will answer hall calls then fault out.
If all else fails, read the instructions
|
|
|
#24312 - 07/12/18 11:01 AM
Re: KCM 831
[Re: Jcjmowrey]
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
It won’t let me scroll through floors at all but it shows what floor the cars at (1,2, or 3) after I cycle disconnect. Maybe it comes from factory with a floor scan from a simulator or test car that’s close to what I have???
If all else fails, read the instructions
|
|
|
#24369 - 07/19/18 12:31 PM
Re: KCM 831
[Re: Jcjmowrey]
|
Joined: May 2013
Posts: 224
Jcjmowrey
enthusiast
|
enthusiast
Joined: May 2013
Posts: 224
Atlanta ga
|
So I tested ,like you described VTR tech, and had to replace all lcehas & lcefcb boards. It then took a lon download and allowed a hoistway scan. Back in service.
If all else fails, read the instructions
|
|
|
|
|
|
|