Who's Online Now
0 registered members (), 12 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#24552 - 08/21/18 08:59 PM TAC32 Fault 115  
Joined: Dec 2009
Posts: 534
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 534
Ims shows 115 car fault code(p2 cross check error) Car runs a week or tow and shuts down again with code. 115 is code in IMS but I can not find that code in the manuals? I found in manual fault 1150 for no pulses on encoder. Is this the same?

#24553 - 08/21/18 09:44 PM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Jan 2014
Posts: 736
Rolly Offline
old hand
Rolly  Offline
old hand

Joined: Jan 2014
Posts: 736
No idea other then this.

Drive Fault: 115
Fault Description:

Multiplexer Configuration Error

#24556 - 08/21/18 11:34 PM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Mar 2016
Posts: 191
lowoil Offline
Elevator guy
lowoil  Offline
Elevator guy

Joined: Mar 2016
Posts: 191
Wisconsin
Hate to get off topic but the 1150 will get you if you dont have z44 set to 100,been burned on that one before and check all new jobs i get.

#24568 - 08/22/18 07:38 PM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Dec 2009
Posts: 534
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 534
Went by this morning to check selector wiring etc. It was one inch below top floor and had not releveled. No faults and it answered the call. When it was shut down before it was at the bottom floor and on the buffer springs. It relevels when we manually lower it. Does the 32 have an adjustable dead zone? We were gong to go back with two people and see how long the dead zone is on it.

#24589 - 08/24/18 03:21 PM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Apr 2016
Posts: 25
Dandroid Offline
newbie
Dandroid  Offline
newbie

Joined: Apr 2016
Posts: 25
Try turning in on the low pressure adjustor, maybe a quarter turn. I've worked on a few I2/3's which had the tension in the adjustor weaken over time and under certain conditions would time out trying to re-level because it didn't have enough juice to move the car on low speed.

Not sure what that fault would indicate though. If I remember correctly (maybe from a thread here, and things I've seen in the field), earlier TAC32 software would check for certain parameters on start-up and trip strange faults because a hydro has different parameters than a traction and the software was looking for traction parameters. Later versions perform that check later on in the start-up after it knows its a hydro. I may be mangling this explanation but functionally this is what you get, and maybe that 115 is related?

#24613 - 08/28/18 12:35 AM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Mar 2015
Posts: 80
Whadafack Offline
journeyman
Whadafack  Offline
journeyman

Joined: Mar 2015
Posts: 80
Check your leveling strainer

#24674 - 09/05/18 11:35 AM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Dec 2009
Posts: 534
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 534
Update on this one. After cleaning strainers it went down again. One of the guys increased the run monitor time a little. Has not faulted out yet.

#24676 - 09/05/18 04:11 PM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Dec 2015
Posts: 1,529
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,529
Local 18
Then it’s an 1150 and Z44 was too low

#24677 - 09/05/18 04:22 PM Re: TAC32 Fault 115 [Re: solidstate]  
Joined: Mar 2016
Posts: 191
lowoil Offline
Elevator guy
lowoil  Offline
Elevator guy

Joined: Mar 2016
Posts: 191
Wisconsin
Z44 must be set to 100 or 10 seconds!


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.187s Queries: 15 (0.045s) Memory: 2.7085 MB (Peak: 2.9004 MB) Zlib disabled. Server Time: 2024-03-29 07:30:32 UTC