Who's Online Now
0 registered members (), 5 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,466
Posts36,641
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#27515 - 07/26/19 10:44 PM GAL MOVFE CAN BUS  
Joined: Jan 2017
Posts: 35
NONVISIONWINGS Offline
newbie
NONVISIONWINGS  Offline
newbie

Joined: Jan 2017
Posts: 35
Hello,

To enable Can bus on the door operator it says to change parameter 11. Parameter 11 does not exist even when it says to place door op in setup mode to be able to change parameter 11. Signal feedback is being recieved in the machine room from the door operator, however the door operator does not appear to be accepting CAN open close and nudge signals. Parameter 11 probably allows that. No idea why I cannot get into parameter 11. Any help would be great. Thanks.

#27517 - 07/27/19 12:28 AM Re: GAL MOVFE CAN BUS [Re: NONVISIONWINGS]  
Joined: Dec 2015
Posts: 1,527
Indirtwetrust Online content
ElevatorPractitioner
Indirtwetrust  Online Content
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,527
Local 18
What kind of controller are you putting it on?

#27518 - 07/27/19 01:17 AM Re: GAL MOVFE CAN BUS [Re: Indirtwetrust]  
Joined: Jan 2017
Posts: 35
NONVISIONWINGS Offline
newbie
NONVISIONWINGS  Offline
newbie

Joined: Jan 2017
Posts: 35
GAL Galaxy IV

#27519 - 07/27/19 01:28 AM Re: GAL MOVFE CAN BUS [Re: NONVISIONWINGS]  
Joined: Apr 2017
Posts: 96
UpandDown2321 Offline
journeyman
UpandDown2321  Offline
journeyman

Joined: Apr 2017
Posts: 96
Not all that familiar with the MOVFE but looking through the manual there are bit settings to view the status of the operator switches. However unlikely...maybe the setup toggle is no good? You should probably see the bit turn on and off and it looks like that needs to be on to access parameter 11.

#27520 - 07/27/19 02:42 AM Re: GAL MOVFE CAN BUS [Re: UpandDown2321]  
Joined: Jan 2017
Posts: 35
NONVISIONWINGS Offline
newbie
NONVISIONWINGS  Offline
newbie

Joined: Jan 2017
Posts: 35
Thanks. I pretty much ruled out the setup switch not working as I had to put it on setup to allow default centre opening parameters to be written to the drive. However maybe there is more than one pole or input. You never know.

Last edited by NONVISIONWINGS; 07/27/19 02:43 AM.
#27526 - 07/27/19 11:46 PM Re: GAL MOVFE CAN BUS [Re: NONVISIONWINGS]  
Joined: Jan 2017
Posts: 35
NONVISIONWINGS Offline
newbie
NONVISIONWINGS  Offline
newbie

Joined: Jan 2017
Posts: 35
You have to set parameter 15 from zero to 6301. Then parameter 11 is visible. 🙄. Hidden secrets.

#27577 - 08/06/19 08:15 PM Re: GAL MOVFE CAN BUS [Re: NONVISIONWINGS]  
Joined: Jan 2015
Posts: 117
Turbo6 Offline
member
Turbo6  Offline
member

Joined: Jan 2015
Posts: 117
Chicago
Are you talking about parameters on the door operator? I just recently installed 4 of these with any issues. Are your red communication lights flashing on canbus card on door operator? Is your jumper on board setup properly for front or rear door?

#27578 - 08/06/19 10:13 PM Re: GAL MOVFE CAN BUS [Re: Turbo6]  
Joined: Jan 2017
Posts: 35
NONVISIONWINGS Offline
newbie
NONVISIONWINGS  Offline
newbie

Joined: Jan 2017
Posts: 35
All working. Needed password 6301 to get in and change. No jumpers for these movfe. Just params. Maybe the movfr has a jumper. I'll find out when I do one of those soon.

Last edited by NONVISIONWINGS; 08/06/19 10:14 PM.

Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.034s Queries: 15 (0.014s) Memory: 2.7004 MB (Peak: 2.8848 MB) Zlib disabled. Server Time: 2024-03-28 12:47:32 UTC