|
0 registered members (),
14
guests, and
4
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums13
Topics6,525
Posts36,929
Members8,461
|
Most Online117 Jan 16th, 2020
|
|
|
#28386 - 12/04/19 05:15 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
I hooked up my fast tool to car station ..I had no response from device I unplugged all connections to CLC besides the top connector and still had no response from device. I replaced CLC and selector board and still have no response from device. I did power off and reboot each time I unplugged connectors. I hooked up service tool to nearby dmc to make sure service tool is good. Car runs on inspection. What is the TC ? Traveling cable ? This all happened after piston seals where replaced
Last edited by Tech9; 12/04/19 05:30 PM.
|
|
|
#28387 - 12/04/19 07:09 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
85. ohms across PSC and NSC. Power supply is good
Last edited by Tech9; 12/04/19 07:15 PM.
|
|
|
#28389 - 12/04/19 09:42 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
Yes I have plugged in all ports. Toc machine room and Car panel . I read between psc and nsc. Watchdog led is steady red on clc. Selector board and door board lights are on also. Does anyone have power supply part number
Last edited by Tech9; 12/04/19 09:43 PM.
|
|
|
#28391 - 12/04/19 09:46 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
Its front door openings only. I. do have spares. But they are shielded. Not sure if have spares like that in tc Should I disconnect Psc and nsc in machine room and car station panel and check continuity. ?
Last edited by Tech9; 12/04/19 10:04 PM.
|
|
|
#28392 - 12/04/19 10:51 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Dec 2015
Posts: 1,541
Indirtwetrust
ElevatorPractitioner
|
ElevatorPractitioner
Joined: Dec 2015
Posts: 1,541
Local 18
|
|
|
|
#28400 - 12/05/19 02:45 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
I got communication after hooking all original boards and software back up. Now I’m trying to do learn run and getting a 10 fault on selector. Pulse count indicates out of door zone Possible my sensor board behind selector board is bad?
Last edited by Tech9; 12/05/19 02:46 PM.
|
|
|
#28404 - 12/05/19 05:05 PM
Re: Dmc fast program
[Re: Tech9]
|
Joined: Aug 2016
Posts: 755
Jluff
old hand
|
old hand
Joined: Aug 2016
Posts: 755
|
|
|
|
|
|
|
|