Who's Online Now
1 registered members (Rique925), 12 guests, and 1 spider.
Key: Admin, Global Mod, Mod
August
S M T W T F S
1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30 31
Newest Members
On my own in 5, Nola50r, kimtaehyun, Local2chi, NYC Mech 29
6139 Registered Users
Forum Statistics
Forums13
Topics4,840
Posts29,308
Members6,139
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#28345 - 12/02/19 11:55 AM DMC. RER ?  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
Hello. Trying to do a learn run after power outage and programming lost. Every time I gets to the 2nd floor magnets I get a RER which is reset error flag command from CLC. What do you guys think the problem is ? Bad selector board ? A side note. My clc is only letting me set it up as the master car of a group. But it’s a single car. No group

Last edited by Jluff; 12/02/19 12:11 PM.
#28347 - 12/02/19 01:16 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
It also will not let me set up valid floor openings which I have never seen before

#28348 - 12/02/19 02:36 PM Re: DMC. RER ? [Re: Jluff]  
Joined: May 2015
Posts: 161
wltr00 Offline
member
wltr00  Offline
member

Joined: May 2015
Posts: 161
Sounds like the power outage may have corrupted your software.

#28349 - 12/02/19 02:37 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
I think once I saw error code saying it didn’t get slow down when run learn failed and RER showed on tool

#28351 - 12/02/19 05:11 PM Re: DMC. RER ? [Re: wltr00]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
I have never replaced DMC software. Only the clc board but used existing chips. Does world electronics sell software chips ?

#28352 - 12/02/19 05:27 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
Today I went to try run learn again and now I get no response from device when service tool is connected. . I isolated the clc board and still got no response from device. Tomorrow I will replace clc and put the existing chips in the new clc .. now I’m really getting confused as to what’s going on. Lol.

#28353 - 12/02/19 05:42 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Jan 2014
Posts: 691
Rolly Offline
addict
Rolly  Offline
addict

Joined: Jan 2014
Posts: 691
Does your board have 3 chip plus ram or 4 chip plus ram? A new board will require the 4 chip software. I believe it's ver DK13. If you have more then one car, all will have to be updated if duplex or triplex.

Last edited by Rolly; 12/02/19 05:45 PM.
#28354 - 12/02/19 06:40 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
I see 3 chips with DMC1 stickers on them from the existing board

#28355 - 12/02/19 06:41 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
I can send you a picture if you PM me your email

#28364 - 12/03/19 01:40 AM Re: DMC. RER ? [Re: Jluff]  
Joined: Dec 2015
Posts: 1,025
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,025
Local 18
I’m not sure about that RER but older software didn’t support the valid floors parameters yet so probably nothing wrong there. There are basically 2 types of CLC cards. Old ones like BP1, BP2 and the first one that just had a number and then there is the BP4. Software is not interchangeable between the 2 types. DK13 is the latest for the BP4 boards but for the older it’s AN13. If you have an older board and all you can get is a BP4, you will need new software.

#28369 - 12/03/19 02:31 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
The new green clc has no ram
Chips in the U32 (SP23) and U33 (sp45) spots. The new clc only has a chip in the U31 spot .. the new board will not boot up with the software chips from the old board. Should I bring boards to computer technition to transfer chips from old board to new board ?

#28372 - 12/03/19 05:06 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Jan 2014
Posts: 691
Rolly Offline
addict
Rolly  Offline
addict

Joined: Jan 2014
Posts: 691
LOL ALL computers have ram. The chip may be soldered in but it has ram! 3 chip software will not work on a new board. I think you been told this before,

#28373 - 12/03/19 06:24 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
I recognize ram on both boards. They are not set up the same and there was no markings on the board. I couldn’t tell if bp1 or 2 or 4. I think it is a bp1. And my new board is bp4. Just learning and trying to do my job Rolly

Last edited by Jluff; 12/03/19 06:27 PM.
#28377 - 12/04/19 12:15 AM Re: DMC. RER ? [Re: Jluff]  
Joined: May 2015
Posts: 161
wltr00 Offline
member
wltr00  Offline
member

Joined: May 2015
Posts: 161
Should have part number 6300BPx right on board, but older versions are blue & newer versions are green. The software between old & new boards is not compatible.

#28380 - 12/04/19 02:47 AM Re: DMC. RER ? [Re: Jluff]  
Joined: Dec 2015
Posts: 1,025
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,025
Local 18
Like I said, the old software will not work in your new BP4 CLC. You either need to find a good BP2 or earlier or order DK13 software.

#28403 - 12/05/19 05:03 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Aug 2016
Posts: 270
Jluff Offline
enthusiast
Jluff  Offline
enthusiast

Joined: Aug 2016
Posts: 270
Got a new BP1 CLC and Im all set. Back to original problem during hoist way set up for 3 stop car. Getting fault missing slowdown when at 2nd floor. Switch tree is out play at 2nd floor. Cams are at terminal landings only. I Pulled up tree anyway and everything looks good. Magnets look good also

#28409 - 12/05/19 10:55 PM Re: DMC. RER ? [Re: Jluff]  
Joined: Dec 2015
Posts: 1,025
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,025
Local 18
Sounds like it thinks it’s a 2 stop


Photo Gallery
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Uncle Dad Here?
Refurbished Elevator Equipment
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.038s Queries: 15 (0.006s) Memory: 2.7747 MB (Peak: 3.0356 MB) Zlib disabled. Server Time: 2020-08-14 22:11:12 UTC