Who's Online Now
0 registered members (), 13 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
April
S M T W T F S
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,488
Posts36,754
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#31282 - 06/18/21 01:14 AM Dover prints needed  
Joined: Sep 2015
Posts: 23
Robert H Schmidt Offline
Scrapwood99
Robert H Schmidt  Offline
Scrapwood99

Joined: Sep 2015
Posts: 23
looking for prints or any info on this controller its hydro submersible 4 stop think it composite .thanks in advance this link should show pics. [] https://photos.app.goo.gl/nRTfK5ZyyxytMs6V7

Last edited by Robert H Schmidt; 06/18/21 01:22 AM.
#31287 - 06/18/21 11:34 PM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Nov 2009
Posts: 410
Johnny Offline
Journeyman
Johnny  Offline
Journeyman

Joined: Nov 2009
Posts: 410
Portland. Oregon
That is a four stop solid state card rack controller. Are you an owner, or a mechanic??? Why do you want prints?? What city are you in??

#31288 - 06/19/21 01:38 AM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Sep 2015
Posts: 23
Robert H Schmidt Offline
Scrapwood99
Robert H Schmidt  Offline
Scrapwood99

Joined: Sep 2015
Posts: 23
Mechanic ,job is Philadelphia suburbs car goes out on low oil occasionally relays have been replaced all cards also replaced .low oil timer adjusted all the way out .is there any way to extend that time, other than the pot?

#31289 - 06/19/21 02:18 AM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Apr 2020
Posts: 396
Montana Offline
enthusiast
Montana  Offline
enthusiast

Joined: Apr 2020
Posts: 396
You might have a valve problem.

#31290 - 06/19/21 02:38 AM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Sep 2015
Posts: 23
Robert H Schmidt Offline
Scrapwood99
Robert H Schmidt  Offline
Scrapwood99

Joined: Sep 2015
Posts: 23
Think they have replaced valve not sure if adjusted correctly have to look into that also tac the car next te there. Just wondering when u order the solid state boards are they job specific could I have the wrong board for this configuration is there difference between say a 2 stop to a 4 stop on the timer for each of these controls

#31298 - 06/22/21 12:44 AM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Nov 2009
Posts: 410
Johnny Offline
Journeyman
Johnny  Offline
Journeyman

Joined: Nov 2009
Posts: 410
Portland. Oregon
Cards are not job specific. There are three slot and four slot cards. Higher number of slots will replace lower number of slots, i.e. a four slot board will replace a two or three slot board of the same type. If you have an I-2 valve, make sure the screen in the leveling adjustment id clean.

#31321 - 06/24/21 02:32 AM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Sep 2015
Posts: 23
Robert H Schmidt Offline
Scrapwood99
Robert H Schmidt  Offline
Scrapwood99

Joined: Sep 2015
Posts: 23
So the timer pot on the power board there was about 1/8 turn left ,increased that an so far car still running but no more adjustment left.also customer has a oil burner heater in room maybe may still have problems as the weather changes and that thing fires up not sure. But thanks for your help on this johnny

#31324 - 06/25/21 04:09 PM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Feb 2013
Posts: 759
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 759
ohio
Usually, Dovers of that era had a bimetal sensor or some type of thermostat in the tank. when the oil got cold the thermostat would call for heat and the pump motor would turn on and run on bypass till the oil heated up. Those Dover valves would not move the car if the oil was cold, they would run till the oil got warm enough or the Low Oil Timer tripped. I would check the thermostat before replacing anything.

#31445 - 07/19/21 06:09 PM Re: Dover prints needed [Re: Robert H Schmidt]  
Joined: Sep 2015
Posts: 23
Robert H Schmidt Offline
Scrapwood99
Robert H Schmidt  Offline
Scrapwood99

Joined: Sep 2015
Posts: 23
This tank has been replaced years ago I know the thermostats your taking about hi and low

think they were just removed so far the car has been running good thx for the help


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.041s Queries: 15 (0.009s) Memory: 2.7086 MB (Peak: 2.9001 MB) Zlib disabled. Server Time: 2024-04-16 18:36:37 UTC