|
0 registered members (),
14
guests, and
4
spiders. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|
|
1
|
2
|
3
|
4
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
Forums13
Topics6,525
Posts36,929
Members8,461
|
Most Online117 Jan 16th, 2020
|
|
|
#33894 - 09/19/22 03:38 PM
Tac 20 entrapments
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
Hi guys and girls. I am getting Tac 20 entrapments .. it seems to happing leaving the top terminal landing. About half of the car door was showing .. I get 1009 init SD Down. I replaced selector boards and problem didn’t happen for a while. But now it happened again lol. No gaps in magnets on back of tape. Any ideas. ? Sometimes there is a 1057(encoder) and once a 1004 (locks).
Last edited by Tech9; 09/19/22 03:42 PM.
|
|
|
#33901 - 09/20/22 11:01 AM
Re: Tac 20 entrapments
[Re: Tech9]
|
Joined: Aug 2014
Posts: 113
KSNY
member
|
member
Joined: Aug 2014
Posts: 113
|
what type of pistons? It could be a packing issue if its a 2t or 3T jack. Did you check the valave strainers? What about the shoes? Maybe to much play at the top floor clipping an interlock
I like elevators and cars. Be Smart Work Safe!
|
|
|
#33907 - 09/20/22 07:46 PM
Re: Tac 20 entrapments
[Re: Tech9]
|
Joined: Nov 2016
Posts: 57
Tech9
journeyman
|
journeyman
Joined: Nov 2016
Posts: 57
|
It’s a in ground jack . I did not check strainers. It’s a I2 valve. I’m replacing selector shoes and car guide inserts Waiting for them .. do you think the 1009 (init SD Down) Is shutting the car down . Or is it the selector codes.
Last edited by Tech9; 09/20/22 07:46 PM.
|
|
|
#33930 - 09/22/22 04:29 PM
Re: Tac 20 entrapments
[Re: Tech9]
|
Joined: Aug 2016
Posts: 755
Jluff
old hand
|
old hand
Joined: Aug 2016
Posts: 755
|
I looked at 2 other Tac 20s. On these the MUTS relay was mounted above the main cpu board on a terminal strip with coil wires marked underneath and with a Separate fork connectors where I see the suppressor plugged into . On the Tac 20 with this problem the MUTS relay is on the main cpu board. Im not sure where the coil gets energized. I do not have print specific for this controller layout. I do see MUTS on con 23….it’s a 5 pin connector. MUTS is labeled for #5 slot. It has 2 control wires on that terminal. I didn’t trace them yet .. I’m still working on getting the suppressor.. may have one soon and I will share my info on it
Last edited by Jluff; 09/22/22 04:36 PM.
|
|
|
#33948 - 09/25/22 10:25 AM
Re: Tac 20 entrapments
[Re: Tech9]
|
Joined: Aug 2016
Posts: 755
Jluff
old hand
|
old hand
Joined: Aug 2016
Posts: 755
|
|
|
|
|
|
|
|