Who's Online Now
0 registered members (), 11 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
April
S M T W T F S
1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,486
Posts36,749
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#36934 - 02/22/24 07:18 PM Tac 32 GAL MOVR  
Joined: Dec 2009
Posts: 536
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 536
Taking over a new job that is in an industrial building. Tac32's with GAL operators. Right now the car doors are on close with button(from inside the car) only, the building wants it where its open with button only also. They want door close and open buttons at the hall stations. At first I thought it would give door watch dog faults, but then it hit me TK must have the door operator wired to the controller through an interface board. As its not faulting out now over the door left open until some one closes it. We will get a better look at this in March. However, looking for input if someone has seen this set up before and guidance on how to remove auto open, without causing any faults on the controller.


As far as the door close/open switches at each floor, my first thoughts are will have to put a floor zone switch at each floor to feed that floor's open/close circuit.

#36937 - 02/22/24 08:11 PM Re: Tac 32 GAL MOVR [Re: solidstate]  
Joined: Feb 2013
Posts: 759
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 759
ohio
How will this affect fire service?

#36938 - 02/22/24 08:25 PM Re: Tac 32 GAL MOVR [Re: solidstate]  
Joined: Dec 2009
Posts: 536
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 536
Presently the doors do close on fire service. This was done by others.

#36949 - 02/23/24 06:24 PM Re: Tac 32 GAL MOVR [Re: solidstate]  
Joined: Dec 2015
Posts: 1,535
Indirtwetrust Offline
ElevatorPractitioner
Indirtwetrust  Offline
ElevatorPractitioner

Joined: Dec 2015
Posts: 1,535
Local 18
That should work. As an alternative to physical zone switches you could add discrete pi outputs and a relay for each floor in the controller. Of course you’d have to pull more wire to the controller this way, 3 wires per floor.

#36950 - 02/23/24 06:44 PM Re: Tac 32 GAL MOVR [Re: solidstate]  
Joined: Dec 2009
Posts: 536
solidstate Offline
addict
solidstate  Offline
addict

Joined: Dec 2009
Posts: 536
Thanks, either way have to pull more wire. Probably more with the floor zone switches. Already will have to pull the wire for the door open/close buttons at each floor. Thanks again.

Last edited by solidstate; 02/23/24 06:45 PM.

Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.030s Queries: 14 (0.008s) Memory: 2.6779 MB (Peak: 2.8350 MB) Zlib disabled. Server Time: 2024-04-15 06:38:23 UTC