Who's Online Now
0 registered members (), 19 guests, and 0 spiders.
Key: Admin, Global Mod, Mod
March
S M T W T F S
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31
Newest Members
Prairieelevator, Robot Rob, Montkone, Jevans, Clayshooter
8395 Registered Users
Forum Statistics
Forums13
Topics6,468
Posts36,656
Members8,395
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#6900 - 05/04/13 01:58 AM TAC 50-04 UIM  
Joined: Sep 2012
Posts: 30
Ibconelson Offline
Rag Man
Ibconelson  Offline
Rag Man

Joined: Sep 2012
Posts: 30
West Tex
Hey Guys,
I have some TAC 50-04's with tape selectors, quite often these units go out on Unintended Motion faults. I am wondering if someone else has been or knows of someone who has been fighting this problem on the tape selector jobs. The 50-04's I have with encoders,transducers and veins work fine but the tape selector job just isn't right. Any info would help. Work Safe.

#6908 - 05/04/13 06:34 PM Re: TAC 50-04 UIM [Re: Ibconelson]  
Joined: Apr 2012
Posts: 4
as722 Offline
stranger
as722  Offline
stranger

Joined: Apr 2012
Posts: 4
Take a look at the position encoder speed while the car is at a floor and not moving. If the speed is going up and down you have a noise issue. Check for ac voltage on some of your traveling cable spares. Disconnect the shields on pa, pa-, pb and pb- and see if it goes away. If it does you have a bad ground.

#6938 - 05/08/13 02:15 AM Re: TAC 50-04 UIM [Re: as722]  
Joined: Sep 2012
Posts: 30
Ibconelson Offline
Rag Man
Ibconelson  Offline
Rag Man

Joined: Sep 2012
Posts: 30
West Tex
Thanks as722 and your absolutly right, unfourtunately I have been down that road. This happens on 4 duplex banks scattered around the complex but never on the simplex unit, we compared the simplex to the duplex and everything is the same with regards to noise and grounding. No noise and building ground is perfect and bonding perfect. There is no direction, demand or velocity when it happens. Never have entrapments when it happens.

#6940 - 05/08/13 09:41 AM Re: TAC 50-04 UIM [Re: Ibconelson]  
Joined: Apr 2012
Posts: 17
Eric Offline
stranger
Eric  Offline
stranger

Joined: Apr 2012
Posts: 17
Is unintended motion fault the only fault when this happens, or do other faults happen with same time stamp.

#6941 - 05/08/13 10:29 AM Re: TAC 50-04 UIM [Re: Eric]  
Joined: Sep 2012
Posts: 30
Ibconelson Offline
Rag Man
Ibconelson  Offline
Rag Man

Joined: Sep 2012
Posts: 30
West Tex
Same faults on all UIM shutdowns, 1904,1655 and 1030.
1904- Detection of unintended motion
1655- RGOK signal dropped
1030- DLB/DLT active at same time.

#6955 - 05/09/13 03:42 PM Re: TAC 50-04 UIM [Re: Ibconelson]  
Joined: Aug 2012
Posts: 38
Rick Offline
newbie
Rick  Offline
newbie

Joined: Aug 2012
Posts: 38
Illinois
Governor rope jumping up and down at releasing carrier on stopping is another cause of UIM

#6956 - 05/09/13 03:48 PM Re: TAC 50-04 UIM [Re: Rick]  
Joined: Aug 2012
Posts: 38
Rick Offline
newbie
Rick  Offline
newbie

Joined: Aug 2012
Posts: 38
Illinois
Sorry I guess I wasn't paying attention when you said you have tape selector instead of governor encoder. At any rate another thing to check is brake set properly and reader head tape guides worn or dirty selector head sensors

#6957 - 05/09/13 03:54 PM Re: TAC 50-04 UIM [Re: Rick]  
Joined: Feb 2013
Posts: 65
Oleeightball Offline
journeyman
Oleeightball  Offline
journeyman

Joined: Feb 2013
Posts: 65
Southeast
Is it 16 bit or 32 bit controller, might consider checking software version and see if its the latest greatest just something to check.

#6965 - 05/10/13 12:34 AM Re: TAC 50-04 UIM [Re: Oleeightball]  
Joined: Apr 2012
Posts: 4
as722 Offline
stranger
as722  Offline
stranger

Joined: Apr 2012
Posts: 4
Are you getting a red fault led on the drive when it happens ? Is it a 16 bit ?

#6966 - 05/10/13 01:42 AM Re: TAC 50-04 UIM [Re: as722]  
Joined: Sep 2012
Posts: 30
Ibconelson Offline
Rag Man
Ibconelson  Offline
Rag Man

Joined: Sep 2012
Posts: 30
West Tex
Hey Rick, brake is good and selector and tape clean, selector boards have been updated to latest revisions. And Oleeightball, this has a CPUA (32 bit) board, generic software has ben updated about two months ago. AS722, no drive faults are present. This has gone on since the mod installation, an engineer has been out and is comming back out soon. I have found out they have taken off the tape selectors and installed veins on a couple of units in Colorado for the same reason and that this is not an isolated case. I wonder how many guys have fought this? Work Safe everyone.


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.061s Queries: 15 (0.018s) Memory: 2.7171 MB (Peak: 2.9185 MB) Zlib disabled. Server Time: 2024-03-29 08:19:01 UTC