|
|
|
0 members (),
43
guests, and
3
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums13
Topics7,385
Posts40,944
Members10,040
| |
Most Online3,137
Apr 9th, 2026
|
|
|
|
Joined: Dec 2013
Posts: 10
stranger
|
|
stranger
Joined: Dec 2013
Posts: 10 |
I responded to a shutdown this morning and found the car at the top landing. Hall calls and car calls latch, doors close but the elevator does not move. Went to the control room, there are no faults. I put the car on inspection and tried to run it down. My locks, gate, safety and direction inputs go high when I try to run in the down direction but the car does not move, I do not get the main contactor to pick. The car does run in the up direction so I am assuming it is the down normal limit that is bad. I didn't find any normal limit switches in the shaftway. Are the normals virtual? Anyone have any advice?
|
|
|
|
|
Joined: Mar 2015
Posts: 69
Shaking the Bush!!
|
|
Shaking the Bush!!
Joined: Mar 2015
Posts: 69 |
Does it have a down directional limit? Maybe open not allowing it to run down. Not familiar with this system but have had it on Otis and TK systems. Both times it was the inspection down direction limit.
When every circuit board is made. They put a little magic smoke inside.
|
|
|
|
|
Joined: Aug 2015
Posts: 4
stranger
|
|
stranger
Joined: Aug 2015
Posts: 4 |
Directional limits are in the form of cigar switches mounted to the cab and the magnets are on the rail. The limits plug into the cartop box.
|
|
|
|
|
Joined: Dec 2013
Posts: 10
stranger
|
|
stranger
Joined: Dec 2013
Posts: 10 |
Do you happen to know the jump #'s for the down direction limit on the KCM. There are no job prints and I can't access the top of car without moving it down first. Any help is greatly appreciated.
|
|
|
|
|
Joined: Aug 2013
Posts: 116
member
|
|
member
Joined: Aug 2013
Posts: 116 |
My guess is a bad HAS BOARD. Kinda need a second set of eyes to see when you turn the key that your getting your door locks. Access is set up as a virtual hoist way . I've had this before , where hall call is lit and the car is there. New HAS board followed by a 5-7-1 LON download, then pull the disconnect.
Good luck
|
|
|
|
|
Joined: Sep 2014
Posts: 170 Likes: 2
member
|
|
member
Joined: Sep 2014
Posts: 170 Likes: 2 |
Depending on what type of unit you have, will dictate where the directional switches are located. Do you know if it's an ecospace, monospace or an mr? New or mod package? You said the main contactor doesn't pick when you attempt to run down so I can assume it's not a hydraulic.
Last edited by BRG; 08/07/15 09:23 PM.
|
|
|
|
|
Joined: Nov 2013
Posts: 93
journeyman
|
|
journeyman
Joined: Nov 2013
Posts: 93 |
Check that 77U and 77N LED's are not both active.
If both are active you will need to swipe one with bi-stable magnet to resolve issue.
Last edited by koneisland; 08/10/15 12:13 PM.
|
|
|
|
|
Joined: Oct 2013
Posts: 120
member
|
|
member
Joined: Oct 2013
Posts: 120 |
Go to menu 4, sub-menu 1, and see what third number is?
Should read 4-1-0
0=normal mode
1= inspection
2= drive sync. Problem
3= fire service
|
|
|
|
|
|
|
|
|
HW PM
by Chris, January 13
|
|
|
|
|
|
|
|
|
|
|
|
