|
|
|
0 members (),
23
guests, and
2
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums13
Topics7,385
Posts40,939
Members10,040
| |
Most Online3,137
Apr 9th, 2026
|
|
|
|
Joined: May 2017
Posts: 26
YORKIE
|
|
YORKIE
Joined: May 2017
Posts: 26 |
Hi Guys
I'm currently working on an old Otis ms300 with a go1 board fitted (Lb11 updated version) I have no manuals and cannot for the life of me remember the button sequence to enter and update the parameter list, I know switch 3 has to be down and sw2 scrolls thru the parameters and sw1 shows the data? but cant remember how to change this data and save, I need to change the board for the updated version due to a fault but need to get all the parameters out and re-enter into new board. can some one help please
|
|
|
|
|
Joined: May 2017
Posts: 26
YORKIE
|
|
YORKIE
Joined: May 2017
Posts: 26 |
PS any manuals on this would be appreciated
|
|
|
|
|
Joined: May 2017
Posts: 26
YORKIE
|
|
YORKIE
Joined: May 2017
Posts: 26 |
Hi
Have managed to replace the board and input the parameters but lift will not run, I think they maybe something wrong with the parameter setup I have a manual for the new LB2 board but really need a list for the old board to allow me to compare to see what may be the problem? any help would be gratefully received. from a frustrated engineer!!!
|
|
|
|
|
Joined: Oct 2017
Posts: 2
stranger
|
|
stranger
Joined: Oct 2017
Posts: 2 |
Hi. Paulwato. You have the Service Tool. Or in the event of a malfunction, what kind of light diodes do not shine and how does the 7 segment indicator behave? Sorry if not a correct translation I'm from Russia. 
|
|
|
|
|
Joined: May 2017
Posts: 26
YORKIE
|
|
YORKIE
Joined: May 2017
Posts: 26 |
Hi bears85 just acquired a service tool but no manual for it? not been back to site with it yet. all LED appear correct , display flashes 0.at present when you put a call in R/Ramps(manual thru car) lift ,DFC lights up for safeties but lift does not run no contactors energise Really could do with manuals for service tool and old LB board
|
|
|
|
|
Joined: Nov 2017
Posts: 1
stranger
|
|
stranger
Joined: Nov 2017
Posts: 1 |
The Elevator must be on inspection to change parameters. On the latest version of the LBII you can plug the service tool.
Last edited by phil_41; 02/05/18 08:38 PM.
|
|
|
|
|
Joined: Feb 2018
Posts: 8
stranger
|
|
stranger
Joined: Feb 2018
Posts: 8 |
The new LBII board has 16 additional HEX memory spots over the original LB board. There are 3 parameters you need to set to 0 to enable the lift to run.
40 (J) phase failure
41 (BCD) brake current monitor
42 (MPD) motor protection device - themisors
The original LB board did not have these features so they must be disabled.
|
|
|
|
|
|
|
|
|
HW PM
by Chris, January 13
|
|
|
|
|
|
|
|
|
|
|
|
