|
|
|
0 members (),
14
guests, and
2
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums13
Topics7,385
Posts40,939
Members10,040
| |
Most Online3,137
Apr 9th, 2026
|
|
|
|
Joined: Jun 2014
Posts: 33
Slayer
|
|
Slayer
Joined: Jun 2014
Posts: 33 |
Having a leveling issue, some floors are perfect while others are off a quarter inch.No reason for vanes to have moved.Wont recognize learn trip.
|
|
|
|
|
Joined: Jul 2013
Posts: 206
enthusiast
|
|
enthusiast
Joined: Jul 2013
Posts: 206 |
What do you mean by won't recognize?
|
|
|
|
|
Joined: Jun 2014
Posts: 33
Slayer
|
|
Slayer
Joined: Jun 2014
Posts: 33 |
Tool says abort , car stops before reaching the needed 0 value at the bottom landing to initialize learn run.
Slayer
|
|
|
|
|
Joined: Jul 2011
Posts: 16
stranger
|
|
stranger
Joined: Jul 2011
Posts: 16 |
Try replacing your batt ram chips if it wont take learn run
Last edited by hotsauce04; 04/06/18 10:00 PM.
|
|
|
|
|
Joined: Apr 2018
Posts: 5
stranger
|
|
stranger
Joined: Apr 2018
Posts: 5 |
Bump up ntsd tolerance to about 500 and try it. Then set it back.
|
|
|
|
|
Joined: Dec 2015
Posts: 1,766 Likes: 11
ElevatorPractitioner
|
|
ElevatorPractitioner
Joined: Dec 2015
Posts: 1,766 Likes: 11 |
Try replacing your batt ram chips if it wont take learn run
When those Dallas RAM chips have been the issue, it has worked for me to just swap the 2. They aren’t bad, just like glitched. Of course I don’t know if this always works.
|
|
|
|
|
Joined: Feb 2015
Posts: 60 Likes: 1
journeyman
|
|
journeyman
Joined: Feb 2015
Posts: 60 Likes: 1 |
Check and make sure your sensors are clean and dont have hoistway junk and dust. run the car down an inspection and make sure NTB goes lower case IN (menu or module ) M 2-1-3-1 i think then make sure ET1.
|
|
|
|
|
Joined: Jun 2014
Posts: 33
Slayer
|
|
Slayer
Joined: Jun 2014
Posts: 33 |
Hey guys I really appreciate the help, I will hopefully get it fixed and will reply back with what the issue was, thx a million!
Slayer
|
|
|
|
|
Joined: Jul 2013
Posts: 206
enthusiast
|
|
enthusiast
Joined: Jul 2013
Posts: 206 |
Only one batram chip is really used, the other is backup. You are leaving the bad one in the backup socket on the board.
|
|
|
|
|
Joined: Jul 2013
Posts: 206
enthusiast
|
|
enthusiast
Joined: Jul 2013
Posts: 206 |
If increasing your NTSD tolerance does the trick, that is a good indicator that your NTSD vane is the wrong length.
|
|
|
|
|
Joined: May 2012
Posts: 194
member
|
|
member
Joined: May 2012
Posts: 194 |
---------worn sheaves on machine and cables will cause cable slippage too much slippage throws the hoistway counts..off
|
|
|
|
|
Joined: Jun 2014
Posts: 33
Slayer
|
|
Slayer
Joined: Jun 2014
Posts: 33 |
Appreciate all the help guys, Len you where spot on, cables are slipping just enough to cause the count to be off.Thanks for your input!
Slayer
|
|
|
|
|
|
|
|
|
HW PM
by Chris, January 13
|
|
|
|
|
|
|
|
|
|
|
|
