|
|
|
0 members (),
25
guests, and
3
robots. |
|
Key:
Admin,
Global Mod,
Mod
|
|
|
S |
M |
T |
W |
T |
F |
S |
|
|
|
1
|
2
|
3
|
4
|
5
|
|
6
|
7
|
8
|
9
|
10
|
11
|
12
|
|
13
|
14
|
15
|
16
|
17
|
18
|
19
|
|
20
|
21
|
22
|
23
|
24
|
25
|
26
|
|
27
|
28
|
29
|
30
|
|
|
|
|
|
Forums13
Topics7,385
Posts40,944
Members10,040
| |
Most Online3,137
Apr 9th, 2026
|
|
|
|
Joined: Dec 2009
Posts: 644
addict
|
|
addict
Joined: Dec 2009
Posts: 644 |
Hall calls work as normal. Car calls answer the call, when car arrives at desired floor, door does not open automatically, have to press D.O.B. or the floor call again. Checked all magnets, parameters, inputs etc. Reloaded software also. Same thing.
|
|
|
|
|
Joined: May 2015
Posts: 71
journeyman
|
|
journeyman
Joined: May 2015
Posts: 71 |
Are you absolutely sure car is not overshooting and leveling back down?. I had this happen to me on Tac 32 hydro , didn't cause faults. I can't recall if it was only car calls that didn't open door, or car and hall.
|
|
|
|
|
Joined: Dec 2009
Posts: 644
addict
|
|
addict
Joined: Dec 2009
Posts: 644 |
Yes we are sure of that have watched i/so and of course we are in machine room injecting calls and know that it is not overshooting
|
|
|
|
|
Joined: Dec 2010
Posts: 639 Likes: 4
addict
|
|
addict
Joined: Dec 2010
Posts: 639 Likes: 4 |
Sounds crazy familiar. Turn it onto Fire Service, then off, and see if that clears it.
|
|
|
|
|
Joined: Aug 2012
Posts: 1
stranger
|
|
stranger
Joined: Aug 2012
Posts: 1 |
Turn D32=2 , sounds like it 0 right now
|
|
|
|
|
Joined: Mar 2019
Posts: 4
stranger
|
|
stranger
Joined: Mar 2019
Posts: 4 |
What type of door operator are you using?
|
|
|
|
|
Joined: Dec 2009
Posts: 644
addict
|
|
addict
Joined: Dec 2009
Posts: 644 |
We were able to get back to the job this week. Tried Phase one and Phase two, still same issue. D32 was on 0, we changed that to 2 and wrt with a reboot. Still same thing. Speed of this job is 125fpm, and speed is fine.
|
|
|
|
|
Joined: Jan 2014
Posts: 736
old hand
|
|
old hand
Joined: Jan 2014
Posts: 736 |
Is there any faults in car with IMS? Also check group.
|
|
|
|
|
Joined: Dec 2017
Posts: 6
stranger
|
|
stranger
Joined: Dec 2017
Posts: 6 |
|
|
|
|
|
Joined: Jan 2014
Posts: 736
old hand
|
|
old hand
Joined: Jan 2014
Posts: 736 |
Might not be a bad idea to change D26=1 then change back to D26=0 since you loaded new software into board. Since you had D32 at 0 no telling what could be wrong. possibly a glitch when loading.
|
|
|
|
|
Joined: Dec 2009
Posts: 644
addict
|
|
addict
Joined: Dec 2009
Posts: 644 |
this may be premature......will know for sure after Thanksgiving. It appears to be the expansion board. We are getting in the 24 volts, but at test points only 16 volts, with all the cons unplugged.
More to follow.
|
|
|
|
|
Joined: Dec 2009
Posts: 644
addict
|
|
addict
Joined: Dec 2009
Posts: 644 |
We hooked up the new expansion board and the same thing. Thyssen thinks bad board, and are sending another one. We will bench test the next one before we hook up and then test afterwards. Keep it updated as we find out more.
|
|
|
|
|
|
|
|
|
HW PM
by Chris, January 13
|
|
|
|
|
|
|
|
|
|
|
|
