TMS 50

0 members (), 7 guests, and 3 robots.

Key: Admin, Global Mod, Mod

Forum Statistics

Forums13

Topics7,385

Posts40,939

Members10,040

Most Online3,137
Apr 9th, 2026

Print Thread

TMS 50 #29852 09/02/20 05:36 AM
Joined: Jun 2020 Posts: 25 New Zealand C crustyone Kiwi
crustyone Kiwi C Joined: Jun 2020 Posts: 25 New Zealand	I keep getting two error codes 50 & 12. Mostly error 12 Anti Creep on a hydraulic lift three floors with a TMS50 controller. Can some one help me solve this one.

Re: TMS 50 crustyone #29855 09/02/20 12:53 PM
Joined: Jan 2014 Posts: 736 R Rolly old hand
Rolly old hand R Joined: Jan 2014 Posts: 736	ANTICREEP FAULT FIRST TIME ERROR: 50 ANTICREEP IN FAULT ON 2 CONSECUTIVE DRIVES ERROR: 12

Re: TMS 50 crustyone #29856 09/02/20 07:43 PM
Joined: Jun 2020 Posts: 25 New Zealand C crustyone Kiwi
crustyone Kiwi C Joined: Jun 2020 Posts: 25 New Zealand	Thanks Rolly. Do you have any idea what would cause this fault. Do I need to do a learn run? If so how is this carried out.

Re: TMS 50 crustyone #29857 09/02/20 07:45 PM
Joined: Jan 2014 Posts: 736 R Rolly old hand
Rolly old hand R Joined: Jan 2014 Posts: 736	Maybe Rope Gripper contact

Re: TMS 50 crustyone #29859 09/02/20 07:49 PM
Joined: Jan 2014 Posts: 736 R Rolly old hand
Rolly old hand R Joined: Jan 2014 Posts: 736	If you don't have a rope gripper could be a dip switch setting. Or Possibly a brake poblem.. micros etd.. Last edited by Rolly; 09/02/20 08:03 PM.

Re: TMS 50 crustyone #29861 09/03/20 05:07 AM
Joined: Jun 2020 Posts: 25 New Zealand C crustyone Kiwi
crustyone Kiwi C Joined: Jun 2020 Posts: 25 New Zealand	Thanks Rolly. This unit is a hydraulic, so no brake. The Governor switch is all good. The dip switch is number 3, tried it in the other position but no change so returned it to its original position. I don't understand your reference to (micros etd) Any other suggestions would be greatly appreciated.

Re: TMS 50 crustyone #29862 09/03/20 06:48 AM
Joined: Apr 2014 Posts: 280 H heisenberg Engineer
heisenberg Engineer H Joined: Apr 2014 Posts: 280	Maybe brake switches need checking?

Re: TMS 50 crustyone #29863 09/03/20 12:19 PM
Joined: Jan 2014 Posts: 736 R Rolly old hand
Rolly old hand R Joined: Jan 2014 Posts: 736	Had a lot of bad boards.. Low end junk system. make sure you get the right board for your silk screen cover if you do get a new board,

Re: TMS 50 crustyone #29872 09/04/20 05:20 PM
Joined: Jul 2020 Posts: 110 Likes: 1 J Jadam member
Jadam member J Joined: Jul 2020 Posts: 110 Likes: 1	Error 50 is Faults on the locking magnet have not caused two faults in succession in my book...

Re: TMS 50 crustyone #29880 09/06/20 12:52 AM
Joined: Jun 2020 Posts: 25 New Zealand C crustyone Kiwi
crustyone Kiwi C Joined: Jun 2020 Posts: 25 New Zealand	Thanks Jadam. What do you mean re the LOCKING MAGNET? can you expand your knowledge on this device. Thanks

Re: TMS 50 crustyone #29897 09/09/20 05:16 PM
Joined: Jul 2020 Posts: 110 Likes: 1 J Jadam member
Jadam member J Joined: Jul 2020 Posts: 110 Likes: 1	Send me you mail address and i will send you the info

Link Copied to Clipboard

Photo Gallery

service tool laptop
by dunkdadrunk, February 4

rip orona
by epic_ecodisc, January 7

what controller is this?!
by Alex_ELMAN, December 4

HW PM
by Chris, January 13

Drive sheave
by jkh, October 10

The best helper.
by Adrian, August 8

Home Forums General Discussion Technical Questions TMS 50