Who's Online Now
0 registered members (), 29 guests, and 1 spider.
Key: Admin, Global Mod, Mod
October
S M T W T F S
1 2 3 4 5
6 7 8 9 10 11 12
13 14 15 16 17 18 19
20 21 22 23 24 25 26
27 28 29 30 31
Newest Members
LocalElevator, edgtg, KaiP411, D. Rickert, Safety Shoes Pro
8738 Registered Users
Forum Statistics
Forums13
Topics6,707
Posts37,792
Members8,738
Most Online117
Jan 16th, 2020
Previous Thread
Next Thread
Print Thread
#36844 - 02/13/24 01:06 AM Kone elevator  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
Working on a kdl16
We got fault 0108 .we check and found encoder wheel defective.
Replace the wheel know We getting fault 0102.
We had to remove the weights to carry the lift below the top rloor

#36846 - 02/13/24 11:13 AM Re: Kone elevator [Re: denzelevator1]  
Joined: Jun 2019
Posts: 118
MX4 Offline
member
MX4  Offline
member

Joined: Jun 2019
Posts: 118
What is the sub code of 0102?

#36849 - 02/13/24 03:43 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
The subcode I am getting is 2002

#36850 - 02/13/24 04:23 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
Fault 0102
Subcode 2002
That is the only fault coming up

#36853 - 02/13/24 07:06 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Jun 2019
Posts: 118
MX4 Offline
member
MX4  Offline
member

Joined: Jun 2019
Posts: 118
Drive DC over current fault

Measured drive DC current too high.
Wrong elevator parameters
Mechanical problem hindering movement
Broken or disconnected LWD feedback.

#36854 - 02/13/24 07:07 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Jun 2019
Posts: 118
MX4 Offline
member
MX4  Offline
member

Joined: Jun 2019
Posts: 118
Check your load weigher 5-1

#36876 - 02/15/24 03:20 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
The load menú 5 1 is at 0%
Menú 6 1=50
Menú 6 2=.5
Menú 6 3=1ms
Menu6 4=400
Menú 6 6=400
Menú 6 7=2
Menú 6 10=50
Menú 6 11=1000

The liftcapacity is 630kg
Every time I change it and try to move the lift it goes back to 400

#36877 - 02/15/24 03:22 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
Once change 6. 4. to 630kg it goes back to 400 kg

#36878 - 02/15/24 04:37 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Jun 2019
Posts: 118
MX4 Offline
member
MX4  Offline
member

Joined: Jun 2019
Posts: 118
You need to unlock the parameters I believe, 6-95 needs to be 0

#36880 - 02/15/24 06:49 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
Ok thanks much
I will check

#36886 - 02/16/24 06:31 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Jan 2022
Posts: 39
project.elevator Offline
newbie
project.elevator  Offline
newbie

Joined: Jan 2022
Posts: 39
in meanwhile check the motor cable termination at both end.

#36887 - 02/16/24 06:32 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Jan 2022
Posts: 39
project.elevator Offline
newbie
project.elevator  Offline
newbie

Joined: Jan 2022
Posts: 39
Also, don't forget that you have to save Drive Parameter before reset.

change 6-99 to 1 for save.

#36896 - 02/17/24 02:08 AM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
Ok thank you !

#36908 - 02/20/24 08:02 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
Good day all

So I got peogrammed all drive parameters.

I checked motor connection on both ends.

I actually replace the drive but same fault 0102.

Subcode 2002.

I was thinking of the load weighing device base on the subcode.
Can it be bypass

#36909 - 02/20/24 08:03 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
It is the strain Guage type connected to the ropes

#36911 - 02/20/24 08:50 PM Re: Kone elevator [Re: denzelevator1]  
Joined: May 2012
Posts: 14
denzelevator1 Offline
stranger
denzelevator1  Offline
stranger

Joined: May 2012
Posts: 14
.

#36913 - 02/20/24 10:44 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Feb 2013
Posts: 771
john jay Offline
old hand
john jay  Offline
old hand

Joined: Feb 2013
Posts: 771
ohio
Are you picking the Brake/Brakes?

#36916 - 02/21/24 03:03 AM Re: Kone elevator [Re: denzelevator1]  
Joined: Jun 2019
Posts: 118
MX4 Offline
member
MX4  Offline
member

Joined: Jun 2019
Posts: 118
So it started with a 108 fault and now a 102, both faults share load weighing issues. What kind of load weigher is it? What’s the part number for it or do you have a picture of it? Have you check 5-1 on all floors? Check load weigher connections? Check load weigher board? 6-75-65 will also show you load weigher input value in mA

Last edited by MX4; 02/21/24 03:10 AM.
#36952 - 02/23/24 09:35 PM Re: Kone elevator [Re: denzelevator1]  
Joined: Jan 2022
Posts: 39
project.elevator Offline
newbie
project.elevator  Offline
newbie

Joined: Jan 2022
Posts: 39
First question is the car moving in RDF mode? (up and down from control panel)

Because Wight issue s for Normal ride (rated speed in car call)

PM me if you need help.


Photo Gallery
PECCO PH5000 Overspeed Governor
Drive sheave
The best helper.
Rotary Oildraulic
Old Otis badge.
Brakes,Coil,Rotor
KONE MX10 repair tool kit
Powered by UBB.threads™ PHP Forum Software 7.6.0
Page Time: 0.040s Queries: 15 (0.009s) Memory: 2.7916 MB (Peak: 3.0596 MB) Zlib disabled. Server Time: 2024-10-04 07:37:12 UTC